Aftermarket Z-Grip products.

[luke]

Blue and Red.


Front View




Z-Grip panels $30.
Available in Black or Raw Blue and Red.





Foregrip extenders $28
Available in Black or Raw Blue and Red.
Comes with mounting screws.
Can be used with ALL AGD grip frames.
For use with AM/MM rails.


Z-15* Reverse FG Extender.
Available in Black or Raw Blue and Red.




Z-15* Forward FG Extender
Available in Black or Raw Blue and Red.

(Disregard the screw sticking up from the FGX, I have low profile screws that will ship with your extender)




Z-Straight FG Extender

Available in Black or Raw Blue and Red.




CFL Panels $35
Available in Black or Raw Blue and Red.
These are "ULE milled" to reduce weight, they weigh 2.3 ounces (That is 1.15 oz each!)
Your frame must be drilled and tapped to use these panels; they will NOT mount to the factory screw holes.
They are made to fit the CFL milled frame, but can be used on un-milled frames also.


CFL Z-grip (ULE) $30
This mod reduces the weight by almost half.
The weight of the frame after it is milled is 6.2 ounces. (Weighed without trigger, panels and safety)


Z grip Blade trigger. $29
Available in Black or Raw Blue and Red.

[PBCapo]

luke...i don't even have a z grip but thank you...in case i ever get one haha

[Cow hunter]

i like the look of those panels(3 line), if you decide to do a run id buy, not in glittery silver though

[A-Tach-One]

Luke as you know I have the offset rail but when those panels are ready, I will take a pair.

[RoamingStorm]

can you change the angle or the side it leans on?

-RS

[luke]

Luke as you know I have the offset rail but when those panels are ready, I will take a pair.

With or without the lines? I probably won't do both... :)

[luke]

can you change the angle or the side it leans on?

-RS

You lost me, what angle?

[luke]

i like the look of those panels(3 line), if you decide to do a run id buy, not in glittery silver though

Will be available in gloss black or raw as shown...

[luke]

Oh yes, up next is reverse 15* foregrip extenders.

I'm doing a small run now, so these will be instock in a limited number PDQ. The design will be the same as the shorter one I make, but for the Z-grip of course...

[A-Tach-One]

With or without the lines? I probably won't do both... :)

With the lines then.

[RoamingStorm]

Can you change what side the tank rests on?

[A-Tach-One]

Can you change what side the tank rests on?

Sure flip the offset rail around. Can't change any angles on it though. I love mine.

[Cow hunter]

Oh yes, up next is reverse 15* foregrip extenders.

I'm doing a small run now, so these will be instock in a limited number PDQ. The design will be the same as the shorter one I make, but for the Z-grip of course...

will it work with the RTP rail?

[luke]

Can you change what side the tank rests on?

A-Tack-1 is right, it can be mounted on the left or right, other that that is is not adjustable...

[luke]

will it work with the RTP rail?

These are being made for the AM/MM rail. BUT if you pre pay I'll mill the wings off and drill and tap 2 mounting screw holes so it can be used with the RT pro rail...

These are just about done (Z-grip-reverse 15* FG extenders), I'll have pictures and prices up tomorrow...

15* forward and straight FG extenders for the comming in the next few days.

Still concidering a Z-blade trigger...