I want to but I have to wait...

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Daniel Morse
    Team Sweep/RT to the core
    • Nov 2000
    • 202
    #1

    I want to but I have to wait...

    to buy the Superbolt because I am using a Warp-Feed off of a Z-Grip on an RT. Which means due to the declination of recoil with the Super-Bolt my warper won't cycle the way it normally does with my stainless steel bolt. So I have to wait for the EZ-Grip to come out in order to buy the Super-Bolt. Then I won't have to depend on the vibration sensor of the warp. That stinks! So basically I am saying, "Tom hurry up with the EZ's" (jK)
    RT
    Z-Grip, Max-Flo 4500psi 88cu
    New AGD longer bolt
    Lapco Bigshot 12"
    12v X-Board Revolution with Warp Feed
    Steel braided hose with on gun input gauge
    Psychoballistics Drop Forward

    http://hometown.aol.com/dj112495/myhomepageindex.html
    Tags: None
    • a_malfunction
      Damnit! It Malfunctioned!
      • Feb 2001
      • 1779
      #2
      A warp wont spin with the superbolt?
      -Gig 'Em Ags!

        Comment

        • irbodden
          Registered User
          • Dec 2000
          • 3413
          #3
          Yeah, the Warp will tend to skip with a Super Bolt, it reduces the recoil THAT much. Xzion was having some problems with it infact.

            Comment

            • magc68
              i see "alive" people
              • Oct 2000
              • 1382
              #4
              just put a microswitch in your zgrip. the channel that the sear sits in is pefect. i have a post somewhere on here on how to setup a zgrip intellifeed style. i did 3 of them. very easy.

                Comment

                • Xzion
                  Official Dragon of AO
                  • Jan 2001
                  • 1617
                  #5
                  Current Z-Grip Intellifeed Installation

                  As stated earlier, I was having problems with my warp, it could be due to the bolt, but it could also have been the warp, as I was having problems with it feeding even before getting the superbolt, worst comes to worst, you just set teh warp to run continously and install an on/off switch to turn it off between games, and yeah, there is a method to install a inteliifeed into current Z-Grips, im planning on doing it to my Z-Grip once I get a chance, ive included a link to the thread mentioned earlier below.

                  Z-Grip Inteliffeed Instructions

                  View My Mags

                  "Think First, Think Fast, Be Careful, Pursue. Be Great."

                    Comment

                    • DarkPhoenix
                      Advanced Fire Support
                      • May 2001
                      • 719
                      #6
                      I believe it is posible to use the superbolt with the warpfeed, you just have to further adjust the sensor sensitivity.

                      "The BEAST"
                      "No-Rise" E-mag
                      Level 10 Bolt
                      AGD Flatline 91cu in/4500psi
                      Black HALO B

                      "Red Heatseeker"
                      Red to Clear Fade Freak Factory Impulse
                      68/4500psi Max-Flo
                      Red HALO B

                        Comment

                        • Xzion
                          Official Dragon of AO
                          • Jan 2001
                          • 1617
                          #7
                          DarkPhoenix; I had my warp set to its highest sensitivity setting, short of having it run continuiously, and it still didnt feed consistantly, but as I said before, I was having problems with my warp earlier, so it might have aided the problem.

                          View My Mags

                          "Think First, Think Fast, Be Careful, Pursue. Be Great."

                            Comment

                            • magc68
                              i see "alive" people
                              • Oct 2000
                              • 1382
                              #8
                              Xzion,
                              thanks for diging up my link. u dont need a maching shop to do the work though. should take u all ofa min to drill a little hole. then just run the wire through to the microswitch. bend the level so that the switch activates when u want it to and presto. u r done.

                              if u need any help just post and ill see it

                                Comment

                                Previous template Next
                                Working...