Now with warp feed and melted hopper. Dan and I tried to install the triggernomics trigger last weekend, but we couldn't get the stock trigger out, that trigger pin is damn tight!!!
Side view:
Side view:
-
black Xtreme Emag
LVL 10 inside, warp feed left setup
green warp feed and green 12V Revvy with X-board (melted for warp hose)
14" Freak kit
Triggernomics blade trigger
AGD flatline 4.5k 68cui with green tank cover
green LED Display (thanks Have Blue)
clear grips with custom sledgehammer logo (made by Load SM5)
to do list:
- Get Triggernomics custom milling
- Get Custom Anno -
Top view:black Xtreme Emag
LVL 10 inside, warp feed left setup
green warp feed and green 12V Revvy with X-board (melted for warp hose)
14" Freak kit
Triggernomics blade trigger
AGD flatline 4.5k 68cui with green tank cover
green LED Display (thanks Have Blue)
clear grips with custom sledgehammer logo (made by Load SM5)
to do list:
- Get Triggernomics custom milling
- Get Custom Anno -
And here's what it looks like from the receiving end
:
black Xtreme Emag
LVL 10 inside, warp feed left setup
green warp feed and green 12V Revvy with X-board (melted for warp hose)
14" Freak kit
Triggernomics blade trigger
AGD flatline 4.5k 68cui with green tank cover
green LED Display (thanks Have Blue)
clear grips with custom sledgehammer logo (made by Load SM5)
to do list:
- Get Triggernomics custom milling
- Get Custom AnnoComment
-
NICE MAG! I tried to get my trigger out too so i could polish it and had the same problem. I like your set up!
Originally posted by PyRo
Its called jokeing. You have no right to be questioning me with your measially 460 posts!!!!Comment
-
There is a way to take those trigger pins out. When I am out in the field I have and adjustable automatic punch used for marking metal, it is around the size of a pen. Well you push it into the pin and the force of the punch is strong enough to take the pin out, but you have to make sure your doing it the right way. Which is the oppisite way the pin was pushed in. It usaully will take two to three punches to take it out. If it dosen't move on the first try maybe your trying to take it out the wrong way. It works the same way to put the pin back in. Hope this helps.
Saul Ramirez
Airgun Designs
E-mag Tech.
Production ManagerComment
-
I love the gun, but is there a better way to setup your warp/hopper to have the hose at a straighter angle? THe first pictures ever taken of these beauties showed the hose at a perfect downward curve, but without a hopper. I'm sure you'd have to melt a hopper down quite a bit for a good fit.Comment
-
or just drill a hole. thats what I'm plannin on. I know it takes down that amount of balls you can have in it, but melting it down would do tha same and I'm sure it would do more damage toBlack Warp Left E-mag #EM00163
emagnum board
14in freak
12v smoke warp w/ interlink
drilled 12v revy w/ JMJ impeller and WAS turbo rev board
shocktech drop
AGD flatline dovetail adaptor
68 3000 flatline
***soon to be***
emagnum body rail
black powder coat
custom grips from FrymarkerComment
-
Well, attaching the warp the way I did gives a tigther fit than running the hose just straight down. Plus, if a did it that way, the hopper would be further back, making my setup back heavy.
I didnt want to drill the hopper for two reasons:
1st: I don't like holes that can let water and/or dirt get into my hopper.
2nd: With the melted hopper, if the warp malfunctions/breaks, I can just take the hopper out of the warp and slap it on my center feed module.black Xtreme Emag
LVL 10 inside, warp feed left setup
green warp feed and green 12V Revvy with X-board (melted for warp hose)
14" Freak kit
Triggernomics blade trigger
AGD flatline 4.5k 68cui with green tank cover
green LED Display (thanks Have Blue)
clear grips with custom sledgehammer logo (made by Load SM5)
to do list:
- Get Triggernomics custom milling
- Get Custom AnnoComment
-
i think u have way too much money(not that its bad)Xtreme AND angel AIR jeeeze!
Comment
-
Greets Manuel
.:| levelx retro z-minimag |:..:| spearhead #192 |:.
.:| ---> looking for Flatline 4.5K or AA Apokalypse 2K <--- |:.Comment
-
I love you Now you can send it over here and let me hold it for you, to make sure it works properly, forever.
Why go to the light, when darkness has its warmth too....
Brak "I poop in the sink."
EPIC - Warp - 68/45 Armageddon
Black 2k LCD
Green 99 Dark AngelComment
-
www.ShartleyCustoms.com
Custom Paintball Products and Accessories
CLICK HERE to Check out our PDU SERIES GEAR!
its more like a paper cut that has primadonna's yelling murder... - GlickmanComment
-
Hey sharteley, I prefer different colors too, I just thought, why waste money on an anno job that Dan (Maghog) is gonna ruin anyways?
black Xtreme Emag
LVL 10 inside, warp feed left setup
green warp feed and green 12V Revvy with X-board (melted for warp hose)
14" Freak kit
Triggernomics blade trigger
AGD flatline 4.5k 68cui with green tank cover
green LED Display (thanks Have Blue)
clear grips with custom sledgehammer logo (made by Load SM5)
to do list:
- Get Triggernomics custom milling
- Get Custom AnnoComment
-
www.ShartleyCustoms.com
Custom Paintball Products and Accessories
CLICK HERE to Check out our PDU SERIES GEAR!
its more like a paper cut that has primadonna's yelling murder... - GlickmanComment
-
You bet!!! 
black Xtreme Emag
LVL 10 inside, warp feed left setup
green warp feed and green 12V Revvy with X-board (melted for warp hose)
14" Freak kit
Triggernomics blade trigger
AGD flatline 4.5k 68cui with green tank cover
green LED Display (thanks Have Blue)
clear grips with custom sledgehammer logo (made by Load SM5)
to do list:
- Get Triggernomics custom milling
- Get Custom AnnoComment
Comment