im using a rtp rail and gearheadz body.
im using a rtp rail and gearheadz body.
Would me putting too many shims in my ult cause a problem like this?
i started over and i removed the ult and put in an rt on/off, switched from the gold spring to the red spring, removed all the shims and now i have a blender, my bolt wont stop on anything.... im at a loss for words. im also rting with my tank set to 700 psi.
You should move and summarize your info into a thread of its own. It may be more than a basic level 10 issue. Being that its a mag, it won't be anything serious though.
I did that, but I think your like right on point here. the o-ring on top of my rt on/off was no good, I just pulled it out and it crumpled into pieces. also, theres supposed to be two O-rings on top of it? I thought there was only one?
A smaller oring inside of a larger oring on top of the on/off. Both should be clear. Good to know you are finding things wrong, like combustible orings XD
ok, im back and my question is, the shims adjust the bolt time resetting correct? I currently have none in and I have no leaks, I also have no idea what my velocity is but if I turn it up too much bolt wont stop on things and when I turn it down to where I think is about the range im going to be shooting at it seems it takes the bolt a second or two to completely reset.
im asking so when I do make it out to the field and crono my gun I know if im thinking correctly or not. thanks again guys
When you test the level 10 operation, make sure you are placing the object directly on the front of the bolt face and not more than 1/4" in front of the bolt. If the object is more than 1/4" from the front face, the bolt will strike it with full destructive force and not the reduced level 10 force.
The bolt spring should always be able to push the bolt back to the reset position without hesitation. If the bolt takes a second or two to reset, it usually indicates that the carrier is tight and restricting the bolt movement.
thanks again athomas, I believe im all good to go now.
Level 10 issues here.
I think the culprit may be a worn gold spring, as I've tried everything else.
I removed all the shims, and worked my way with the carriers to the best fitted one, with no leaks.
I'll pull the trigger and the lvl10 will kick in, but most often then not, I'll have to reset the bolt by pushing it back.
Aside from being a worn spring, is there anything I should look at?
well, if you used the largest (loosest) carrier that doesn't leak (using the same o-ring with the different sized carriers), and the bolt is not resetting after a breech obstruction, i would first oil the lvl 10 o-ring, then if that doesn't help try a different spring. seems like you're on the right track.
i've found the gold spring hits too hard though; it would reset during a breech obstruction but crack the paintball in testing. you may want to try a red spring, or a cut-down silver spring (place cut end towards bolt). or maybe the gold spring i was using was a regular lvl 7 spring...i don't know. use a spring that hits hard enough to push a paintball into a tight bore without resetting, but soft enough that it doesn't crack a paintball if you hold it halfway in the breech.
When you fire the gun and hold the trigger in, how long does it take before the bolt stops weeping air out the front? If the answer is that it never stops, then it is more likely an on-off issue. If it stops after a few seconds (even quite a few), then the problem is that the carrier size is too tight. Having a carrier that is too tight even though it is the largest one that doesn't leak is a result of a bad carrier oring. If that is the case, change the oring and go through the tuning procedure again.
When I pull the trigger, it doesn't leak. No matter how long I hold it for. Is that a possible sign of something wrong?
Are you using a stock AGD body and rail? When you dry fire, does the bolt reset? When you hold your hand over the end of the barrel and dry fire, does the bolt reset? When you hold the front of the bolt with your finger and pull the trigger, does it chuff and then reset?
When I hold the front of the bolt, and pull the trigger it chuffs and resets.
Is the body sitting flat on the rail? Make sure the pim on the bottom of the body isn't bottoming out in the trigger frame screw hole area. Also, don't over torque the field strip screw. It can warp the valve - body - rail alignment.
Thank you, athomas! Your consistent replies to these most recent posts has allowed me effectively troubleshoot my own issues.
I discovered that my sear/trigger rod, though new and direct from AGD, was a bit too long for my intelliframe. I was having issues with the on/off until I adjusted the length based on the trigger pulled back with the safety engaged. (credit card thickness now)
I was then able to deal with my Level X issues, which turned out to be 1 carrier size too small. I was able to move up to the next carrier size( from 1 line to 1 line/1 dot) without leaking, whilst addressing bolt stick issues. She is now airtight and fires consistently without issues so far.
ive got a slight leak down the barrel on my valve, thought I had it tuned good went to shoot it today and this, the thing though is that if I slightly hold the trigger no leak... im guessing I have the wrong carrier size?
ive got a x-valve lvl 10 and I just changed all the O-rings in the valve. first time I shot it no leaks, could it be the carrier o-ring loosing up from being broke in giving me the wrong size carrier now?
Hey Thomas, I think the issue that I'm having with my Mag is due to the usage of using brittle paint. I'm talking paint that breaks from dropping it from a foot above the ground. I won't be able to confirm until I take my mag back to the field.
no shims are installed
ill try putting my valve into a different mag, if I still have a problem I guess ill get ahold of tuna
so I think I just might be special :tard: or my power tube tip wasn't tightened all the way. its fine that is all right now, back to the other valve I go, hopefully you don't have to hear from me for a while :p
My setup is an X-valve with ULT on/off. The rest is pretty damn close to stock minimag + intelliframe. The air comes from a ninja SHP pushing ~1200 psi.
About once every 100 shots or so my bolt is having trouble resetting. The gun will shoot, then hiss down the barrel with a limp trigger for a second or three before resetting. I think it happens more often while rapid firing (?).
I've have been using the longest, red spring.
Before this issue came about, I was using the next-half-sized-up carrier. While pressurized, the gun was prone to leaking down the barrel. This leaking would stop when the trigger had some pressure on it - both before and after the gun shot. Power tube oil would fix the leak temporarily, but it would come back within a pod or two. I think even while using this leaky-sized carrier, the medium-sized spring was sometimes having trouble resetting the bolt.
Is it accurate to label what I'm describing as bolt stick? What can I try to do to reduce this given I'm at the biggest carrier that doesnt leak and using the longest spring?
Thanks so much!
is your bolt spring old or worn out? is your grip frame screw too tight, or quickstrip screw too tight (or too loose)? it could cause the valve and body to be mis-aligned. double check that your rail bushing is in the rail. search the tech forum for bolt stick, if you haven't already. there are dozens of threads; you might be able to dig something up.