Printable View
Sorry Willy and joe for the slight hijacking of the warp gurus, but i had a quick question on external vib. sensors. I was reading the warp manuel for the umpteenth time and noticed that i could have an external vib. sensor. Where about are these to purchase and how to I hook it up? It said something about a phone jack.
Well Gib I know that Pro Team products sells the external sensors with their warp so I guess you can ask them about it. JT ok I understand the shematic now and the batteries are in parrallel not in series. All this does really is to keepa good steady supply of voltage and yes from your last coment it does not incease amperage at all because technically there is no voltage increase. That is if I remember right. /shrug
Ok thanks willy. Found some places with them, pretty spendy :( Now trying to find if i can wire them into the agd warpfeed. Man, i think i might have gone the wrong route on this.
if u buy the pro team sensor, it should aready have the little plug, that u plug right into the warp, and then u just set teh sensors to use the plug for activaion
Oh, you mean the little metal hole next to the priming button? If thats it, i wondered what it was for.
Ah well I think I just might break down and buy the PTP 12volt mod. Cant go wrong and I know how to wire it into my warp.
I bought a PTP 12v mod too, just plug it in and go :)
why? i though u understood the schematic
No I understand the shematic fine, but my problem is that no one around here carries the 12 vdc reg that I need. Everyone that I have tried lets around 16 volts though it and it makes my warp run constantly. So since PTP makes em I figure I'll just buy one of theirs and wire it into my warp myself. And one other question just got my Egg in today anybody know how to intelli mod it?
did you try the bigcell? the bigcell mod doesnt need any regulator. and keeps the warp at a fast speed
Well i have found the external sensor (man, every one has these important modding questions, and here i am :rolleyes: )Only problem is that no one seems to have them for sale or i haven't found that special business with them. I can get the Proteams Gen 5 bracket form proteams for about $80 :( , but i want to go cheaper. You guys know of the top of your head a cheap place to find the bracket?
the agd one?
I checked the automag store and didn't see an external sensor setup for their warp. I just assumed they didn't make one. If they do have one, can you please post the link because i just can't find it.
ok now are you looking for a sensor or a warp bracket? your posts in one say u looking for sensor, and ur post 2 posts ago says u want a bracket
Actually the Proteams external sensor is a bracket with a sensor in it.
call them and just be like " yeah i need a new sensor for my warp mine broke off" or something, try and get just the sensor from them
ok now its my turn, anyone know where i can find info on intellifeeding an emag to teh warp, and how to run the warp off the emag battery?
Can someone tell me how i can get a sensor thing for my mag i am not using intelliframe and i wanna know what to do and where to get what i need i have the warp and everything i just need a sensor thing.
are you sure there isnt already one inside the warp like there should be?
Does anyone have a pic of the PTP angel feedneck for warps or know what they look like?
I'm trying to figure out if it is a threaded 90* adapter. If it is I'll get one and place it on the new Warp ULE and see how well that works.
If you have hopper left, can you still have the warp on the lefthand side? I'm right-handed BTW. And can you adjust the angles so the warp is almost in the back of the gun?
yes, just put the 90* adapter on top of the p/f. and yes you can position the plate so the warp sitds farther back.
I think you can put the long power feed tube in the top and make it a bottom feeder.
he could cgi, but he has hopper left, and wants the warp on left side of teh gun. the most compact way he can have it setup is to pop the 90* adapter on the p/f tube and run it straight to the warp. but,
woogie, if you want, i have a p/f right body that i can sell you that would give you a really tight warp setup. lmk
Oh okay. I thought he had hopper left and wanted warp right. That would work if he wanted the warp on the right.
You can adjust the warp in and out. Its level with the grip frame to help balance it
I have read and reread all the sections dealing with installation of the warp feed. I have a standard p/f automag, I bought a clear warpfeed from AGD a few weeks ago, and I have been attempting to install it all day today. I checked the vibration adjuster, bought fresh batteries, and look for any loose conenctions - everything looks liek it is in perfect working order. Although it all "looks" good the dern motor won't turn. ANy clue to what the heck is wrong with it?...Thank you MsDolls
first with teh batt plugged in, press the white prime button, spin?
Im right handed shooter (shoot out the right side of a bunker 70% of the time)but i want a warp mod but i dont know if it is the right feed or left feed that will have the warp/hopper on the RIGHT hand side.
no matter what feed you have, you can put the warp on either side. so i am guessing you want the warp on the left side of your gun? well for the tightest setup you would want to have a warp left body or a power feed hopper right body
i need a quick fix...
im setting up a RT with a warp for my friend.
i have the right jumper on the warp set up accross the bottom two rows (to use the pizo sensor)
the potentiometer (blue tower) turns but doesnt seem to adjust the sensitiviy enough... if i turn i clock wise too much the warp runs constantly... as soon as i back it off just a bit the warp wont spin at all unless i REALLY hit it. am i missing something... i cant figure out how to set the sensitivity so the warp will spin when the gun is fired.
skirts - is it a new warp, has it been broken in? Make sure the mounting plate is nice n tight so it transfers the vibrations properly. Check to see that the warp board is in securely and the springs are making good contact. You may have to swap out vib sensors.
Havoc-I just got my AGD warp in. I originally ordered a pro-team, but found out that I could get the AGD one and still be able to mount it to my Spyder AMG. Now...here comes my problem. I don't want to wait two weeks for Doobie to come back from school and mount it on. I want to mount it on now.
Really wish AGD had step by step instructions with pictures (gotta have pics) so anyone can hook this up themselves. The manual is horrible and I don't know if it's just me, but it all went right over my head. I'm guessing it's not just me bcuz this thread is now 15 pgs long. :D Do you think AGD will come out with some better instructions for people like me who are electronically challenged? :D
it really isnt that hard bro. plug in batteries, screw platte to gun, turn blue knob all teh way clockwise, then turn counterclockwise untill spinnign stops, but then starts again when the warp is tapped by yoru hand or something. that simple enough? :D
Thanks...but I'm not a bro :D In desperation, I asked my husband Doobie and he has started talking me through it. Now it sounds a little easier. It was just kinda overwhelming at first and this is the first time I've done anything to my marker, so I'm still learning. But still think step by step pics would be a good idea, for some of us who like to do things on our own and hate to ask... ;)
woops sorry :o :D
its just like men not wanting to ask for directions. we have a superior sense of direction, better than any on board in car gps system to boot!Quote:
Originally posted by Trina
for some of us who like to do things on our own and hate to ask... ;)
:eek: :rolleyes: ;) :D :D
No problem!Quote:
Originally posted by JT2002
woops sorry :o :D
its just like men not wanting to ask for directions. we have a superior sense of direction, better than any on board in car gps system to boot!
:eek: :rolleyes: ;) :D :D
EXACTLY!!! We just don't want to ask...that just really sucks!! If there are pics and good directions no one knows that you don't know...:D
But now it's too late....you all know that I don't know :( It's out in the open...AUGGGHHHHHH!!!!
Quote:
Originally posted by JT2002
woops sorry :o :D
its just like men not wanting to ask for directions. we have a superior sense of direction, better than any on board in car gps system to boot!
That is exactly why AGD does not include installation instructions with the warp, they know we will not read them anyway :)
My wife just laughs at me when I open something new to assembly and first thing toss the directions away and say: "Well, don't need those!".
lol. i like to do taht too :D , unless i really have no clue what the F im doing, then i "refer" to them:D
But the sad thing is...guys can figure it out, they look, try, look at the parts, try again...and they got it.
As for me, I just know there's this thingy and it should maybe go into the other thingy, unless that thingy doesn't work...then I reread the directions.... ;)