Bad Dog I PM'd you
Bad Dog I PM'd you
MY TRADER FEEDBACK (<--- click here)
Maroon/Black Karta ULE Emag w/Predator board
Red/Black Acid Wash Edge milled Excalibur
***And I'm currently out of stock on both the 90* & 45* adapters***
nice try though
..when u expecting more in?
Dangit. Well if you ever get more, you have a waiting list...
thats actually a good idea,
If you'd like me to do another run, post below... if theres a big enough demand I will do another run... also specify what you would most likly want (90* or 45*) and how many you'd be up for...
no commitment or preorder list... just something so I have a general idea.
yeah i was unaware that it was/mgiht be a limited run type thing but yeah i need a 90* if possible no hurry i have two already but theyr not as slick
if not a 180º, how about something between 90º ~ 180º?
Anything to keep the warp hose as straight as possible.
What type of material are you using anyhow? There are pipe benders out there design to bend pipe without distorting it's shape.
what use would there be for a 180 ? it would just be like an extender....
Originally Posted by wantamag
I don't know how best to explain this, I've tried previously.
Anyhow, here goes again.
I have a centerfeed body which I like in case the warp goes down. If the warp fails for any reason I can just drop my hopper on the centerfeed bypassing any issue with the warpfeed.
My issue with running the warp with centerfeed is, the hose has too many bends that with paint that isn't perfect round (like most tourny's around me) the paint jams in the hose and I have to remove the hose. Sometimes I have to bypass the warp and put the hopper right on the centerfeed. Now I don't have as much faith in my warp as some may have. I like to have the insurance of the bypass option. Though tell me if I'm wrong If I were to swtich to a warp body I wouldn't have as much of an issue since there is only 1- 90º bend instead of 1- 90º bend and the hose bending too much which is encountered in a centerfeed set up let me know please.
I figured any elbow bend more than 90º and less than 180º would keep the hose from bending too far. The straighter the hose the less likely paint will jam in it due to friction and/or out-of roundness.
Ok I hope to be enlightened after this post, PLEASE!
Last edited by Mechanic79; 09-28-2004 at 06:38 PM.
well if you picked up a Warp ULE body, and you ran your hose through the hopper, you could use a 45* adapter... which is actually the most direct route unless you ran the hose direct to the warp ULE...
i think his point is that he cant get a warp body because he wants to keep the centerfeed body in case his warp fails. You might try getting an AGD warp elbow, and then attaching one of Bad_dog's adapters onto that to make a 180* adapter...i think that would work.
Q-Mag COMPLETE!!! Now I just have to get that ugly little **** anno'd
I could use a black 90* adaptor if you start making them again
For your "pre-order" list per se,
I would like to get 2 of each of the black 90 and 45 degree elbows.
Moderate with Equality & Consistency in 2005!
AO-WI: Player's List - Now with over 100 People!!!
Member #007 of the Unoffical Trina Fan Club
Great Traders: automagfreek, ClassicMagger, Emagster, fire1811, Kevmaster, MrMag, Nicad, oldsoldier, RogueFactor, SpongeBobSquarePantsx2 , SteveDx10+, The Frymarker, Treefall25, Tunamanx3, warpfeedmod
In Loving Memory of Eric "Po" Ison Oct. 10, 1974 - Dec. 31, 2004
I have one and LOVE IT! Now, Trina wants one! So...in other words, count me in for a 90*.
The gun is 1/8" of a game that is a FOOT long!
(...but a 'mag helps)
I know I was born and I know that I'll die...the in between is mine. -Eddie Vedder
I seen it first on Doobies mag at Shatnerball. Then I remembered it was Bad_Dog. Must have.
Right on jwalker87, that is a good idea.Originally Posted by jwalker87
hmmm the Trina that happens to be the AGD spoksmodel??Originally Posted by Doobie
Pm me ...
Last edited by Bad_Dog; 09-30-2004 at 09:08 PM.
Originally Posted by Bad_Dog
are you waiting for a certain # or what? the other ones seem to go pretty fast i suppose...and you dont have ANY left.. ?
is it ahrd to run a small batch or you just dont want to udnerorder or what?
I was actually wondering if she indeed wanted to be down for a 90* adapter, versus a 45* which might work better with the warp breech on her Xmag...
And I will be doing another batch sometime here soon...
I'm intereasted in a 90*. Let me know if you have another run.
they're on thier way
Well if this means you're doing another run, put me down for at least one 90*
I'd be interested in atleast one of each
Girls are no substatute of paintball
Murphy's law of paintball: If it jams force it. If it breaks it needed replacing anyways