List of Automag Levels

[AGD]

For all you collectors out there I happened to come across my original listing of the different levels for the Mag and what was done in each. We didn't release the gun until level 5 so previous to that you will not find any. I am posting it here so I don't loose it again!

AGD

68AUTOMAG DESIGN UPDATES



Level 1:

Power tube polished and measured .385 x .600
Power tube spring full ground both sides .285 free length
Power tube insert turned for urethane o-ring and spring
On/off top turned for air flow
On/off pin ground and checked
Bolt trimmed to .275 deep to power piston
Ream inside regulator body for washer clearance
Jumbo nubbins

Level 2 09/21/90:

High strength front frame screw
Trim regulator valve for minimum clearance

Level 3 11/15/90:

Bronze power tube spring
Black spring pack
New twistlock and o-ringed barrel
Slotted power tube insert

Level 4 12/05/90:

Teflon o-ring for on/off valve
Washer for power tube

Level 5 01/01/91:

Rear nubbin ball drop

Level 5.1 02/11/91:

Milled frame to allow .750 pin

Level 5.2 04/09/91:

Extended, drilled power tube tip
Small ID power tube

Level 6.0 05/18/91:

Drop in sear
One piece barrel
Square spring
Wire nubbin
Large air chamber
Power Feed
Crown Point barrel

Level 6.5 08/21/91:

Extended power piston
Countersinked power tube tip

Level 6.6 11/11/91:

Computer designed power tube tip

Level 7.0 04/01/92:

Expanded air chamber with soldered on power tube tip

[LittlePaintballBoy]

Awesome, like a timeline of the mags evolution.

[Target Practice]

Holy crap, my micromag has a level 3 bronze powertube spring. Wicked!

[Muzikman]

TP: the Power Tube Spring was used well into the Level 7's. I am not sure exactly when it was changed over to the spacers, but it had to be about the time the RT came out. I have a TON of the PT springs as they came with every rebuild kit, but hardly ever went bad and by this time I had bought a Pro-Team spacer kit.

Hmm...this info will be good for my AGD time line I am building.

[ScatterPlot]

Sweeet!!!

[spasticsquirrel]

IM AT lv10!!!

i need a walkthrough though..

[Jimbud]

Tom I know we have been over this a few times before but I am a little confused.

What level were the guns that the B's originally got?

I know that they had Knurled Barrels and no slots on the Power tube tips.
I also seem to remember updating to the bronze power tube springs.

Are those guns still in the data base?
the registration dates may shed some light.

Jimbud

[judster]

i still had my bronze spring in when they installed the LX at the 1st shatner...when they pulled it out they gave me a look of shock.....my responce was: 'if it ain't broke, don't fix it' never had a need for the spacers...the spring worked fine for me

[Muzikman]

Tom I know we have been over this a few times before but I am a little confused.

What level were the guns that the B's originally got?

I know that they had Knurled Barrels and no slots on the Power tube tips.
I also seem to remember updating to the bronze power tube springs.

Are those guns still in the data base?
the registration dates may shed some light.

Jimbud

If there are guns out there before level 5...I REALLY need to find one

[gc82000]

The Mag in the old vid that was a level 5 was it not. And werent the design of the level 1 or 2 sold to ICD to make the old school jackal or desert fox not sure on the name?

[Thunder Bunny]

The Mag in the old vid that was a level 5 was it not. And werent the design of the level 1 or 2 sold to ICD to make the old school jackal or desert fox not sure on the name?

I believe so. I found the vid a few weeks ago, my brother got it in the early 90's with his first Minimag. Tom removed a circular clip and took off the power tube. The vid is dated 2-92. Anybody want a copy?

[Beemer]

Tom I know we have been over this a few times before but I am a little confused.

What level were the guns that the B's originally got?

I know that they had Knurled Barrels and no slots on the Power tube tips.
I also seem to remember updating to the bronze power tube springs.

Are those guns still in the data base?
the registration dates may shed some light.

Jimbud

Holy shaaaZam BatMan, Captain JB is here. I smell a Rally. Wanna be the Captain? Can JimBud and the Wizard come out to play.

JB, we malfunctioned the P1, and 2s remember, then the P3 was the first we used in a tournament, wasnt it????? Old age and to many of these has lapsed my memory. You still have your P3 dont ya?

What was the year of level 1? Its not there

If there are guns out there before level 5...I REALLY need to find one

I could tell ya who has 1, but then I would have to ya

Oh Ya Welcome to AO you old S.O.B.

[Jimbud]

JB, we malfunctioned the P1, and 2s remember, then the P3 was the first we used in a tournament, wasnt it????? Old age and to many of these has lapsed my memory. You still have your P3 dont ya?

I thought that the guns we got were lvl 3 or 4 but when I asked tom a while back he said they were lvl 5.

But if the info he just posted here is correct they had to be at least lvl 3 maybe lvl 2


I still have my old gun but it is a mix of levels and proto parts.
I wish I would have had the foresight buy Another gun and leave it original

And this is for the Wiz.

[AGD]

Jimmy you probably did get a level lower than 5 when I first got you the guns. We only released level 5 guns to the PUBLIC.

Hitech yes higher pressure is more efficient, been proven before. The tough part is convincing people that its a good idea.

AGD

[Jimbud]

Ahh thanks, I thought all the 100 series guns were built to the same level.
I didn't know that most were updated before they were sold.

[hitech]

Hitech yes higher pressure is more efficient, been proven before. The tough part is convincing people that its a good idea.

Yeah, but I still want to try. I'm still wondering if it will require any higher pressure than level 10 does now.

Hope you had a good Christmas.

[pump]

wow coolness
i love you AGD

now it would rule to have a list of mags after the the level 7
RTs and up

thats when i get confused
when they came out and design differences

[TAW]

Ok, now I'm confused. I was replacing some orings in these valves and noticed a slight difference.

The one on the right (176) I got in a parts lot from Tom. It has a larger air chamber, no relief valve in the reg piston and the cross cuts on the on/off top are shallow. The powertube is from Jimbud and it has a longer PT tip and no slot.

The one on the left (237) has a smaller air chamber, relief valve in the reg piston, deeper cross cuts in the on/off top and shorter PT tip with a slot for removal. It also has a drill mark were the two halves screw together, you can just make it out in the pic.

So is that how they progressed or was Tom messing around with the one I got from him?

Thanks guys

[AGD]

The smaller air chamber was the original configuration along with the power tube tip with no slots. You have them reversed. The bigger air chamber was hogged out as one of the level updates in order to reduce the pressure.

Thats some pretty original stuff considering we started the serial numbers at 100.

AGD

[TAW]

Once again Mr. Kaye thanks for your time.

[pump]

Awesome!!!!!
Best Thread Ever!!!!!!

[hitech]

The smaller air chamber was the original configuration...

You don't have any of those smaller air chamber valves lying around, do you? If up to date parts fit it would make it easier to prove my efficiency theory.