How To Put An Ego Frame On A Mag

[latches109]

Latches109's guide to putting an ego frame on an automag.

Parts:
*7/32nd drill bit
*SMC SY113A-SG-PM3 [solenoid]
http://www.airsoldier.com has them or order from SMC
http://www.smcetech.com/CC_host/page...,smc,V_M,1115))
this is the break down of the noid SN, if you order directly from SMC
SMC = company,
SY = type of noid in their product line,
1 = 100 series,
1 = normally closed,
3 = piping, body ported,
A = large flow style,
S = 5 Volts,
G = Grommet lead wire .3m,
[don't need a surge suppressor]
[non locking push style manual over ride]
PM3 = Body ported for m3 threads

* A RAM that fits. This is the hard part, I may be able to get more of the one I used but I'm not sure. You will just have to experiment with this part. I have yet to mount the solenoid, and have found it to bounce, and move. This should be eliminated once I figure out the best way to mount it. Mine is wedged in there right now. MPA-3 works. Check out the other emaggo threads. links at the bottom.
*Hose
*barbs
*LPR

Directions:
<a href="http://www.putfile.com/pic.php?img=4894162"><img src="http://img1.putfile.com/thumb/3/6021055048.jpg" alt="Click to enlarge"></a>

<a href="http://www.putfile.com/pic.php?img=4894169"><img src="http://img1.putfile.com/thumb/3/6021055279.jpg" alt="Click to enlarge"></a>
Use the ULT in the valve. Put in lots of shims^^

<a href="http://www.putfile.com/pic.php?img=4894161"><img src="http://img1.putfile.com/thumb/3/6021054960.jpg" alt="Click to enlarge"></a>
Drill the front of the frame like so[but straight]^^


<a href="http://www.putfile.com/pic.php?img=4894163"><img src="http://img1.putfile.com/thumb/3/6021055074.jpg" alt="Click to enlarge"></a>
Line up the frame and rail then mark where to drill for the back

<a href="http://www.putfile.com/pic.php?img=4894164"><img src="http://img1.putfile.com/thumb/3/6021055151.jpg" alt="Click to enlarge"></a>


<a href="http://www.putfile.com/pic.php?img=4894165"><img src="http://img1.putfile.com/thumb/3/6021055150.jpg" alt="Click to enlarge"></a>
remove front arm of sear^^

<a href="http://www.putfile.com/pic.php?img=4894167"><img src="http://img1.putfile.com/thumb/3/6021055278.jpg" alt="Click to enlarge"></a>

<a href="http://www.putfile.com/pic.php?img=4894421"><img src="http://img1.putfile.com/thumb/3/6021591011.jpg" alt="Click to enlarge"></a>
solder noid lead to a 2 pin connector to connect with the board, you can destroy a timmy eye harness for it like i did. or crimp one on if you have the tool. Or buy one here Link like Loguzzzzzz did.

plug it all in
connect all the hoses
get the noid situated just right so the grip closes
air up
power on
and go mowing.

here is some video: http://www.youtube.com/watch?v=wYvKxMlZ_Vo

<a href="http://imageshack.us"><img src="http://img184.imageshack.us/img184/4278/dsc0012hd5.jpg" border="0" alt="Image Hosted by ImageShack.us" /></a>
emaggos:
Latches109 - here

Loguzzzzzz - Thread: https://www.automags.org/forums/showt...78#post2335978
Video1:http://feat.putfile.com/flow/putfile...zzzzz-Emaggo-1
Video2: http://media.putfile.com/code.php?n=Loguzzzzzz-Emaggo-2[url/]

AirAssault -Thread: https://www.automags.org/forums/showthread.php?t=213280