DIY Electronic Parts & Upgrades

[p8ntbal4me]

I am an Authorised Dealer for Scenario Dreams Products.

Listed below are some parts that I offer if you need replacements.

Scenario Dreams Universal T-Board (UTB) Wire Harness = $ 11.50*



Current Stock = 5

Scenario Dreams Universal T-Board (UTB) Membrane Pad = $ 9.00*



Current Stock = 0

Scenario Dreams Universal T-Board (UTB) Membrane Pad w/ 3-prong adapert = $ 10.00*



Current Stock = 5

*does not include shipping
*I will combine shipping on all orders made to a single address

[p8ntbal4me]

Scenario Dreams Universal T-Board (UTB) Break Beam Eyes = $11.50*

Colors Offered: Blue / Green / Orange / Red / White / Yellow



Current Stock Blue = 3
Current Stock Green = 4
Current Stock Orange = 0
Current Stock Red = 4
Current Stock White = 0
Current Stock Yellow = 0

Scenario Dreams Universal T-Board (UTB) Infrared Break Beam Eyes (no color) = $8.50*

Current Stock = 0



*does not include shipping
*I will combine shipping on all orders made to a single address

[p8ntbal4me]

Hyper Frame/Boo-Yaah/E-Blade Sear Solenoids = $ 50.00*



- These come WITH the 1.5mm standard plug needed to connect to a Planeteclipse (E1/E2), Scenario Dreams Ego/E-Blade Main Board
- 48 of these in stock are left over from the original Planeteclipse stock.

Current Stock = 99

Universal T-Board (2-button/Open Bolt) = $ 50*
Comes with:
(1) UTB
(1) 25g Microswitch
(1) Wire Harness
(1) Membrane Pad (power/eye button)
(1) Membrane Pad Connector (may not come with 3-pos connector)
(1) 16volt 6800uf Capacitor
(1) 9volt Battery Connector
(1) Multi-colored LED
(2) Shorth lengths of heat shrink tube


Current Stock = 5

I can also sell JUST the UTB and a wire harness if you do not need the other parts.
PM me for current pricing. Please note that you want just a board and harness.


Here is a short video of BigEvils Hyperframe'ed Mag. He purchased a Open-Bolt UTB kit and a Replacement Hyperframe 35g Switch from me. The rate of fire is 15bps.

BigEvil's UTB Hyperframe Video

DIY Devil Mag Solenoid Tension Block = $ 15.00*

These little blocks bolt on to the Intelli bracket located in most AGD frames
They allow the use of "pancake" type solenoid to actuate the sear.
All hardware is included with each block to mount and use.
Perfect when used with my solenoids listed above!

Comes with:
(1) 8-32 threaded tension screw
(2) 2-56 threadedmoutning screws
(2) 2-56 threaded nuts


Current Stock = 30

Hyperframe Trigger Switch (35g) = $ 10.00*

These are a drop in replacement for the stock 80gram switch that sells with the Hyperframe.
They are made from the same company that made the original! Lighter and far better than the stock switch. You can fan your fingers across your trigger like you would expect to do with any other electronic frame!
(because these switches are BRAND NEW, they have retained their original hole diameter which is slightly smaller than the screws to mount them. You do not need to drill these out! A little extra force when pushing your screws through the switch is all thats needed. Once you install the switch and remove the switch 3 times, you wont notice the difference)



Current Stock = 7

ULE Body Eye Covers
Raw (Unfinished) $ 25.00*
Gloss Black $ 35.00*
Matte (dust) Black $ 35.00*



These eye covers work with the ULE Body only. Comes as a set with the left and right side. Will work with your detents (does not work with detents with larger O.D.s)

You must have a hole drilled and tapped on your rail to hold them in place as well as a wire slot for the wire leads.



Current Stock =
Raw (unfinshed) = 0
Gloss Black = 5
Matte (dust) Black = 5



*does not include shipping
*I will combine shipping on all orders made to a single address

Eye Cover Body & Rail Milling = $100

Luke's Customs can perform this service for you for a small fee. I recommend having Luke's Customs doing this work to insure the proper fit on your rail and body with these eye covers.

*The milling service provided is paid directly to Luke's Customs*

Shown below is a picture of the eyes installed on a customers body and rail with the milling completed by Luke's Customs


*Picture is property of Luke's Customs*

[p8ntbal4me]

16volt 6800uf Capacitor (works with E-Mag Solenoids & Hyperframe Solenoids = $ 2.00*



Current Stock = 25

16volt 2200uf Capacitor (works with Hyperframe Solenoids *not E-Mag*) Smaller than the 16volt Capacitor*



16volt 470uf Capacitor (for use with EP solenoids that are more than 6volts) = $2.00



Current Stock = 50

10volt 10,000uf Capacitor (replacement for the one found in the Devil Mag) = $5.00

Measurements: 18mm (dia) x 26mm (high)



Current Stock = 100

1/16" Heat Shrinkable Tubing (works with UTB Wire Harness Wires) = $2 @ 6"* or $3 @ 12"*



Current Stock = 100'

[flyingpootang]

I need a UTB wire harness. Please pm me your paypal....Thanks

[p8ntbal4me]

Updated stock

~ P8nt

[SSP REAPER]

Jai,

I need everything for an EPG build.

UTB board
Wiring complete with LED and membrane pad
Noid.
Please pm me

[p8ntbal4me]

Luke's Customs is now taking work for the milling of your body and rail to support the installation of my new eye covers! See top of thread for details,....

~ P8nt

[splat15k]

PM sent (yesterday).

[phill7]

you still have the eye covers for sale if you do ill take a pair

[p8ntbal4me]

Added a new Capacitor for use in the Devil Mag

~ P8nt

[Bturkben]

Do you still have products available?