Introducing the Micromag 2009

[dark blade]

dark blade, 1 emag body

the order for me is correct

[Ruler_Mark]

tracy id like to change mine to a e-micro setup, no vert asa or grip needed,,

Also have another question, it looks like trigger frames with 'wings' will work without having them milled is this true?

[The_Joker]

i dont know if that can be done since the vert ASA isnt gas through if i recall corectly, the grip itself would have to be a tube with one hole on the bottom or low on the side and one at the upper portion of the grip itself. unless you figure out how to oring the main screw hole at the top. which can be done then drill and tap the vert asa portion problem solved.

I really wanted to use the gas through the vert ASA like Hgblues even if I had to get a grip from AGD but from what I've read, that's not possible because thay have not drilled & tapped for it..... correct?

Was ther any rationale given as to why the Vert ASA is not dilled & tapped for a gas through???


This thread has gotten entirely too long to keep up with.

[Dend78]

i believe there was talk of a gas thru version but im not 100% sure on that and i could be wrong with my statment but from what i understood is it was not set up for gas thru

[The_Joker]

i believe there was talk of a gas thru version but im not 100% sure on that and i could be wrong with my statment but from what i understood is it was not set up for gas thru

That's actually disappointing.

Correct me if I'm wrong, but wasn't even the MicroMag 2000 set up with a gas thru vert ASA.

I would be willing to pay extra for PTP to drill & tap for a gas thru and I can epoxy the attaching screw to make it airtight after I get it.

What say ya???

[Dend78]

why epoxy? teflon tape should work or even an oring may be able to be used it just needs to be drilled and tapped and 1/8" npt, then you can still take it all apart without getting freaky with a torch. if you epoxy it in you also kill the abilty to turn the breech cause of the 4 mounting screws and the one big one.

[The_Joker]

why epoxy? teflon tape should work or even an oring may be able to be used it just needs to be drilled and tapped and 1/8" npt, then you can still take it all apart without getting freaky with a torch. if you epoxy it in you also kill the abilty to turn the breech cause of the 4 mounting screws and the one big one.

I agree with you totally but was using "epoxy" as an extreme to make my point.

The key point is the need for a gas thru vert ASA and being willing to pay extra to get it.

[Dend78]

I agree with you totally but was using "epoxy" as an extreme to make my point.

The key point is the need for a gas thru vert ASA and being willing to pay extra to get it.

gotcha

[going_home]

What is a gadget grip?
I paid for a Micromag, what all was to be included with the original order?
Was I supposed to get an ASA with my original order?
Whats the story with the vert grip?
What is the MM front?
What is the EM front?

A gadget grip has a barrel plug made into the bottom of the grip like this :



I always do a gas thru foregrip setup so that doesnt work for me.

Not to mention that I dont know of any fields that will allow barrel plugs any more.

Now a Pro team barrel bag I'd be interested in.

And maybe a shorty (8" or 10") Armson barrel too.

[BenoitOWN]

I want the e-mag style version because I want to put an E-Mag Battery Pack ASA Manifold from luke on it.

Question for luke what fits inside the battery cover? Palmer microrock is a bit too tight.

[stircrazzzy]

Tracy,

Can I actually have both fronts? I am not 100% how I want to set this gun up yet, and I want to keep my options open

Thanks!

[luke]

Anyone, am I supposed to email or pm tracy my parts order?

[Dirty Deuce]

Yep, I am officially lost in the sauce.

[luke]

Question for luke what fits inside the battery cover? Palmer microrock is a bit too tight.

To be honest I'm not sure, I don't have a pack to measure and don't mave all the regs to measure either..

[Dend78]

To be honest I'm not sure, I don't have a pack to measure and don't mave all the regs to measure either..

yes the micro rock just doesnt fit but possibly it could be bored out a bit on the sides in the area for it to fit. the one shown in the pics in his dealer thread fits with no issues at all. i still gotta send that in for Luke to look at.

[Ratt]

Tracy - I don't see my order on the list. I would like an emicro body, a vert asa, and a MM front. With those three parts, I should be able to switch back and forth between having a mech micro (using my own vert grip) and a e-micro...right?

[Tracy_ptp]

Tracy - I don't see my order on the list. I would like an emicro body, a vert asa, and a MM front. With those three parts, I should be able to switch back and forth between having a mech micro (using my own vert grip) and a e-micro...right?

As long as you have both fronts.

[Ratt]

Sweet...I would like both fronts.

[Mayzons]

Tracy please add 1 vert asa to my order, thanks

[Ruler_Mark]

tracy id like to change mine to a e-micro setup, no vert asa or grip needed,,

Also have another question, it looks like trigger frames with 'wings' will work without having them milled is this true?

...

[Tracy_ptp]

...

Yes regular mag frames will work.

[Swamp Thing]

Just finalized my order but will post here for completeness

1 E Body Vert ASA, and MM Front as well Gloss Black

1 E Body Vert ASA, and MM Front as well Flat/Matte Black

1 MM Body Vert ASA Flat/Matte Black

That should do it

Thanks

Swampthing

[Tracy_ptp]

Vertical and Gadget grip (it doesn't have a barrel plug in it)

$20 Raw
$25 Anodized

The extra Front pieces (are a little tricky and a lot of work)

$50

[zondo]

Will a hyperframe with wings still on work with this body?

Thanks
Mike Brothman

Wings won't work, but if you have a Dremel handy...

tracy id like to change mine to a e-micro setup, no vert asa or grip needed,,

Also have another question, it looks like trigger frames with 'wings' will work without having them milled is this true?

Yes regular mag frames will work.

[Tracy_ptp]

Sorry my bad, I was confused, needs to be RT style so that it is flat!! I think I am braindead.

[micromag-man]

Tracy,

ok, here's mine

1. micro 2009 setup, vertical and gadget, sear pin, etc., satin black

1. micro 2009 setup, vertical and gadget, sear pin, etc., matte, satin, maybe spec. ano?

1. EMicro 2009 setup, sear pin, etc, matte black

3 frames all together

I will owe an extra $50 in the end for the vert & gadget grips

[zondo]

Sorry my bad, I was confused, needs to be RT style so that it is flat!! I think I am braindead.

It's all good! I'm sure you have nothing else going on other than 2K9 Micromag!

[Mayvik]

Ok, you have me on the list correct with what I ordered...however I also fall into the bucket.

There is no difference between someone who orders a mech version with an extra e-mag front, and an emag version with an extra mech front, correct?

Is ano decided or what? Haven't seen a clear answer yet. Gloss black is my preference if it's available...

The next question, is what did I pay you for?! lol. I think I just paid the total for a complete mech body, and the extra front, vert ASA and vert grip are not funded yet.

Edit: Ok looking back through the last few pages, I'm now confused again. Does the vert ASA automatically come with a mech body? If so, that would mean there IS a difference between people who ordered an E body (they get a body and the E front, and would need to pay extra for both the M front and the VASA), and those who ordered an M body (they get a body, M front, and VASA, and would pay extra only for the E front).

Double

Edit 2: Also, is this coming with a basic cylinder feedneck, or any feedneck at all?

[alkafluence]

What Mayvik said?

I would also like clarification on exactly what comes with it when the following are purchased:

E-Micro setup
Regular Micro setup

[Thotograph]

I'll call in payment thurs... it will be for:



Emag setup and sear pin, gloss black