Page 2 of 2 FirstFirst 12
Results 31 to 39 of 39

Thread: New Warperior Rail Presale - TimmyJay (design) & XMT (milling)

  1. #31
    Join Date
    Mar 2010
    Posts
    3
    Quote Originally Posted by Jaccen
    Wouldn't it also work with Magna internals in a Halo shell? I know you can turn off the tension sensor on it. I do that with my Smartguide setup.
    Yes, the Magna internals in a Halo shell should be fine. The normal Magna shell has the cup and raceway too close to the front so when you would cut it and put on the 90* elbow it would probably be coming out of the front of it.

  2. #32
    Join Date
    May 2007
    Location
    Fox Paintball Territory
    Posts
    779
    Quote Originally Posted by koleah
    Forget the rail-

    Whatever you did to the valve look SICK. Changes the lines of the gun so they just go straight from the back all they way to the tip of the barrel. SO COOL.
    It is cap'd with a threaded back. I planned to put a gauge there, but why, so I ran the macro to it.

    Sorry for the delay. I just got back from Ely, MN fish'n.

  3. #33
    Join Date
    Feb 2008
    Location
    Boulder, Colorado
    Posts
    919
    So, how would a direct right feed classic body sit on there? (after holes are properly trimmed to fit of course)

    Would the feed sit vertical?

  4. #34
    Join Date
    Sep 2011
    Location
    Virginia
    Posts
    139
    Quote Originally Posted by TimmyJay
    It is cap'd with a threaded back. I planned to put a gauge there, but why, so I ran the macro to it.

    Sorry for the delay. I just got back from Ely, MN fish'n.
    How/where do you adjust the velocity?

  5. #35
    Join Date
    May 2007
    Location
    Fox Paintball Territory
    Posts
    779
    Quote Originally Posted by BiNumber3
    So, how would a direct right feed classic body sit on there? (after holes are properly trimmed to fit of course)

    Would the feed sit vertical?
    I didn't have anything to test it, but it would be heading in the vertical direction. If someone lives near Fox Paintball, IL and has one, then we could see (roughly).

  6. #36
    Join Date
    May 2007
    Location
    Fox Paintball Territory
    Posts
    779
    Quote Originally Posted by tigar19
    How/where do you adjust the velocity?
    It is adjusted via the adjustable Reg on my compressed air tank. Using a Dynaflow...

  7. #37
    Join Date
    May 2007
    Location
    Fox Paintball Territory
    Posts
    779
    Adding a short video...It was longer, but I forgot to turn the loader on. Sorry it took so long to post this and for the pathetic trigger work.

    Die Corn Die!


  8. #38
    Join Date
    Sep 2002
    Location
    New Berlin WI
    Posts
    88
    I have been thinking about doing this. I'm somewhat unclear as to which halo will work for this. I have an old halo b and an empire halo. Will either of these work? If not can some of their parts be replaced to make them work. Is it possible to run one of these off an emag battery and use the warp advance wire to make it spin?
    Thanks for any info you can provide.
    Kory
    Micromag rt, 68 ci flatline,12"ss total freak ,warpdrive, 12volt revi.homemade intelliframe.

  9. #39
    Join Date
    Jul 2011
    Location
    United Kingdom
    Posts
    347
    Halo will work but needs to be converted to sound activation using a reloader board

    Eye detection won't feed paint properly on warp conversion

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •