ALL about the WARP-FEED

[ben-afficial]

what senses the vibration, is it a spring or what?

[bushmanbilly]

E-mag,warp,egg, interfaced?

Blew my board, is it possiable to do this.

[E r y k]

ben- if you have the AGD warp, look on the right shell, youll see a round circular thing built into the shell... thats the sensor

bush - yes its possible, did you mod it?

[bushmanbilly]

No I did not mod it. I was cleaning it and a wire came off. So I tried to soder it and fried the little thingamajig that controls the eyes. Is is possiable to connect the interface cable to the eye feeds. this way I will still have use of the borad. And the triger would replace the eyes.

[E r y k]

eyes? or the sensor?

if you just hosed the sensor, you may still be able to use the intelli feed option...

[bushmanbilly]

eyes? or the sensor?

if you just hosed the sensor, you may still be able to use the intelli feed option...

Could you direct me to the info on this option. It would be nice to have my warp and egg runnin off my trigger.

[ben-afficial]

why are you tryin to intelli- your eggo,,,its a force feed with eyes

[bushmanbilly]

why are you tryin to intelli- your eggo,,,its a force feed with eyes

Because I was cleaning it and broke a wire off and then fried the eyes while sodering. This way clear shelled balls would feed. The local field uses RPS Stingers,and sometimes the eyes can't see them. And it would be allmost impossable to out shoot your hopper. Going to the electronic dudes place today to try this, will update later.

[MiniSpdRcr]

Agh where in the world do I put the capacitor in with the 12volt mod??? I keep looking for schematics but no such luck.

[tippy baller]

im gettin alot of hopper hits...can the warp be put on any gun??? im just curious

[tribalman]

Agh where in the world do I put the capacitor in with the 12volt mod??? I keep looking for schematics but no such luck.

well, i should use proper schematic drawings, but i'll put a pic here.
i'm not sure if ur asking how to hook it up, or where do u put it once it's all soldered together. when i did the mod i just took care not to shot any wires and stuffed it in. if i accidently labeled something wrong, or have it wired wrong, let me know so i can fix it.

also, don't use a capacitor. they are used to hold a charge, then discharge at a greater voltage. you will fry something. use a 12volt voltage regulator. ihttp://www.radioshack.com/product.asp?catalog%5Fname=CTLG&product%5Fid=276-1771
if u turn on the batterys and a few seconds later the heat sink is hot. TURN IT OFF RIGHT AWAY! let it cool and check to make sure you aren't shorting it out and it is wired correctly. on the box it should show you the proper way to wire this in. like i said, my picture may be wrong cause i drew it from memory.

[MiniSpdRcr]

Well it just keeps spinning without stopping....and I heard that if you use a capacitor that it will take care of the problem. So far it just keeps spinning freely.

[ben-afficial]

E R Y K: The warp on my mag works great, but the warp on my phantom wont sense vibrations of any kind no matter how much i adjust the sensor, but both warps have same parts. THats why I asked
Tippy baller:A warp can be put on any gun, you just might have to dremel the warp platform a little so it fits with the bottemline screws.

[trains are bad]

This is how you fix the constant spinning problem. Use the smallest cap that works, just spring for the assortment pack they have at radioshack. The constant spinning is caused by noise riding on the DC from the voltage regulator and the cap filters it out.

[Maggot6]

http://store.airgun.com/index.cfm?fuseaction=catalog.prodInfo&productID=39&categoryID=19

I got all happy when I saw the price..And then noticed it was only in pairs.