Logic Ripper EM - The Electro Solution - PreOrder

[CoolHand]

Does this frame only work with the X-valve or can it also work with stock automags. I know it doesn't work with bodys with twist lock barrels but are there bodys that have powerfeeds that aren't twist lock?

The only powerfeed bodies there are, also take twist lock barrels, so they are out.

I have not tested this frame using a classic valve, since they start to shoot down at @16bps, but I can if you think you'd like to run one I'll give it a look. You just won't be able to use the frame to its fullest.

[splat15k]

So how light can the trigger be adjusted? What about pull length?

[CoolHand]

So how light can the trigger be adjusted? What about pull length?

Did you read the first post? This is an electronic frame, IE the only weight that has to be there trigger pull wise is the microswitch, which takes 25 grams of force to actuate (The ULT takes 15ozs of force, or 425 grams of force to actuate). You can adjust the magnetic trigger return force to suit your taste, from totally slack to snappy and crisp, all from the outside of the frame.

Pull length, once again, is the same situation as the pull weight. The only length that has to be there is the ~0.020" that the microswitch needs to move to actually be actuated. The trigger is totally adjustable though, so you can make the pull as long or short as you like, once again, all from outside the frame.

[frogoa]

can it go fullauto or 3 shot burst?

can it go full auto or 3 shot burst

The only powerfeed bodies there are, also take twist lock barrels, so they are out.

I have not tested this frame using a classic valve, since they start to shoot down at @16bps, but I can if you think you'd like to run one I'll give it a look. You just won't be able to use the frame to its fullest.

[11 Bravo]

can it go full auto or 3 shot burst

Yes it can. It has the Predator board.

[CoolHand]

Yes it can. It has the Predator board.

What he said.

[mr.mag218]

i have a morlock, rail milled for eyes, and an x valve with ult. how much will it cost me to get an empty trigger frame, and my body milled for eyes?

[Automaggot68]

i have a morlock, rail milled for eyes, and an x valve with ult. how much will it cost me to get an empty trigger frame, and my body milled for eyes?

It's going to take little more than JUST a board to power the fram, dude.

[CoolHand]

i have a morlock, rail milled for eyes, and an x valve with ult. how much will it cost me to get an empty trigger frame, and my body milled for eyes?

I'll sell you a kit without any electronics for $350, but I will not warranty it at all. If you're OK with that, so am I. (And it's not like I won't know which one I didn't assemble ).

Add $45 if you want me to drill the body for eyes (though if you've already machined the rail, it begs the question ---> Why can't you drill the body yourself?).

[UDO]

How Much Would It Cost If I Already Have Xvalve And Ule Body But Want Eyes And All The Other Goodies

[CoolHand]

How Much Would It Cost If I Already Have Xvalve And Ule Body But Want Eyes And All The Other Goodies

Frame Kit - $450
Slug Rail - $50
Eye Install/Rail Milling - $125
RTP Sear & Axle Assembly - $35
Rail Bushing - $1
Bike ForeGrip - $16
Macro Fittings and Line - $18 (If you want braided SS it will cost extra)
AKA Clamping Feed - $25
Shipping - $15

Total Anodized, Assembled, and Tuned - $735

No barrel, or bottom line ASA.

[Emag2005]

Frame Kit - $450
Slug Rail - $50
Eye Install/Rail Milling - $125
RTP Sear & Axle Assembly - $35
Rail Bushing - $1
Bike ForeGrip - $16
Macro Fittings and Line - $18 (If you want braided SS it will cost extra)
AKA Clamping Feed - $25
Shipping - $15

Total Anodized, Assembled, and Tuned - $735

No barrel, or bottom line ASA.

Don't forget the LPR

[UTDragun]

is it possible that you could use a std jds lpr?

[CoolHand]

so for those of us that preordered, it'd just be +$125 for the eye installs?

That is correct sir.

Don't forget the LPR

Didn't forget it, an ANS LPR is included in the $450 kit.

is it possible that you could use a std jds lpr?

If STD makes a 'cocker type LPR that will thread into an 1/8" NPT port, then yes. Otherwise, no. I know AKA makes SCM's that will work, but I don't think STD has one like that yet.

[CoolHand]

The solenoids came in today.

That just leaves ano and boards standing in the way of assembly and shipment to a grateful world.

I'm thinking they will go off to ano next week (unless the new ano guys are horribly slow on the samples).

At any rate, hopefully World Cup goes well for TAG and they have my boards for me when they said they would.

Wouldn't that be wonderful? A project that is actually running on schedule.

I was begining to wonder if such a thing were even possible.