How To Put An Ego Frame On A Mag

[Bluemag321]

What type of LPR do use ??

[olinar]

any will work, but the orracle tickler is the one most of us used.

very small and a great price. adjustable as well

[latches109]

the third port on the solenoid is a gas vent.


Loguzzzzzz was using a reg from palmer's that looked like the best option. I will see if he can post some pictures of it.

I use an old autococker reg. It works just fine. I think palmer's pursuit shop makes the most consistent lpr though. Mine does creep down in pressure after 2000 rounds or so. I am going to pick up palmer's.

[jbg00d]

then what actuator is it? I think most of us understand the basic principle, but are curious what parts your using.

Well, it looks like one of these:

http://www.bimba.com/Products/FlatCylinders/MiniatureCubeCylinders/

It's what I plan on using. I just bought a new 06 pe ego frame tonight.

[latches109]

Well, it looks like one of these:

http://www.bimba.com/Products/FlatCylinders/MiniatureCubeCylinders/

It's what I plan on using. I just bought a new 06 pe ego frame tonight.

that should drop in nicely.

The mpa3 is an inexpensive option that works great. but you do need to mill the frame a little.

also look at festo.

[Spider-TW]

Well, it looks like one of these:

http://www.bimba.com/Products/FlatCylinders/MiniatureCubeCylinders/

It's what I plan on using. I just bought a new 06 pe ego frame tonight.

That would be really slick, but the bore is a much smaller and the stroke is shorter than an MPA-3. Are you using a ULT?

[p8ntbal4me]

Okay Guys;

For some strange reason I cant find the posts I made in either this Emaggo topic or Logzz,... so Im re-posting again.

I have an 05 Ego frame and I went to AKA to purchase the 2-pin CON for the noid.

The one everyone else is using does not seem to fit in my stock EGO board.

I did a little digging and found that the same connector for the E1/E2 fit this connector.

I dont have a picture of my board, but I do have a picture of a Xonic Cocker board (E1 nock off) that has the female side showing on 2 different angles.



I also have a picture of the noid with the connector I need as well.


If you cant see the port and want to super size the picture, click on it and save to your computer. You should be able to super size the image in the MS Image Viewer.

~ P8nt

[danoxide]

so weather or not to do this to one of my mags has been bouncing around in my head latly, and i have a few questions.

1-anyone ever figure out what ram is to be used for this yet?

2-more of just my mind running, but if you can make an ego trigger frame/electronics work for a mag, and shocker owners can put an ego frame/elec. on there gun, then concivibly(sp?) if i wanted to i could use a shocker frame/electronics?

[p8ntbal4me]

so weather or not to do this to one of my mags has been bouncing around in my head latly, and i have a few questions.

1-anyone ever figure out what ram is to be used for this yet?

2-more of just my mind running, but if you can make an ego trigger frame/electronics work for a mag, and shocker owners can put an ego frame/elec. on there gun, then concivibly(sp?) if i wanted to i could use a shocker frame/electronics?

Problem with the shocker is it uses 2 boards working as one.

One on the noid, one in the frame.

Probley can be done,... but with experience working with Angels old and new,.. and the fact of the shocker STILL using 26 gauge wire that loves to break easy when creating custom mod work,.... I would say its not a good idea as far as electronics go.

[p8ntbal4me]

I found a connector that works with the stock EGO board I have.

The connector from the COPS/SENSI in an Angel IR3 is the correct one.

Looking at the ones I got from AKA,.. they are smaller in width, as well as the pins are closer together in the housing.

My frame is done. I have to see what the rails look like when they come back from Gruntball to see which one I am going to use. I have a Micro Mag body I sized it with to get the holes drilled. Once that is all set Im going to send my EGO frame and my IR3 frame out to anno to match everything up.

This frame took some planning and thinking to keep the install clean, but is by far the easiest mod to do. Now that I know how much to mill and where to place the insides,... I figure 4 hours tops to get it done.

Thanks Latches109!

~ P8nt

[latches109]

P8nt - would like to see it when it's finished. just remember the ego boards output 6V where that noid pictured needs 9V.

danoxide - use an mpa3 or a small double acting ram from festo. yes you can use a shocker frame but not the noid since it is a 4 way manifold mount where you would need a 3 way body ported for the mod. I would imagine the shocker board would work...not sure how you would get around the harness.

[p8ntbal4me]

The noid with the 3-barbs on it that people have switched to has a coil voltage of 5vdc.

The noid in the picture thats a "pancake" is only for the connector reference (see little red circle)

~ P8nt

P8nt - would like to see it when it's finished. just remember the ego boards output 6V where that noid pictured needs 9V.

[latches109]

The noid with the 3-barbs on it that people have switched to has a coil voltage of 5vdc.

The noid in the picture thats a "pancake" is only for the connector reference (see little red circle)

~ P8nt

oh ic

[RiotKing]

this seems to be the place to ask, so...
i wish to make the happiness that is the egomag, but, i have my eyes on a certain frame. do any of you know or think that the E-Tek STARS frame will be a good choice? it states that it is compatible with all ego versions, so the re-drilling of the attachment holes should be the only thing to do, right? also, it dosent look to have anything pneumatic going on, is it fully electronic?? and it seems i am going to be needing a new noid, which are the best choices and WTB??
any answer would be nice, thank you.

[Sumthinwicked]

gee my friend has a ego frame for sale its one of those special aftermarket ones to :P http://www.automags.org/forums/showthread.php?t=225725