Yea he hasn't been on since October 11th. Maybe someone try PMing him over on Custom Cockers?
-
I think this has become a scam. Garth has not been on in almost a month. I bet his business is closed down or he just could care less. Once work slows down for me I plan on raising hell like I did to get the frames, if the LPR has not shown up.
where is all that Canada BBB and Canada internet fraud government division info I had....oh wait here it is....
Tick tock tick tock...Comment
-
Update guys.
I broke two oring grooving tools on these LPRs. The first the two had 1/8 dia shanks which are too fragile for sidewall grooving.
Just got another one made for me with a 3/16 dia shank. Should work with no problem.
The LPR consists of three main parts. The upper section which houses the large adjustment spring and pistion. this is the low pressure chamber as well. The middle section is the high pressure chamber that houses the small pin. The low section is the end cap .
The problem is trying to milling an oring groove in middles section which has little or no room for a tool to get into to make the oring groove.
This LPR is difficult to make since I have never made such a tight fitting full size LPR. Once a machine is free possibly by Wed or Thurs I"ll finish one off and post the pic of it.
GarfComment
-
How about posting a pic of your broken machine?Pewter SFL E-Mag #EM01569
Pewter Shocktech Intimidator
My Trading Feedback
Extraordinary Traders:
Johnny Bravo
Good Traders:
fcpchop, Xerces, Piccolo, hawpunch, Boble86, NCpaintballer, Chupas2, shrapnel, gump1119, Methos, PunkOff, TheFlamingKoosh, RogueFactor, JonesieComment
-
Can you change the trigger on this frame? I want to get one and maybe put a splinter or viperblade on that frame.sigpicComment
-
Its pretty sad that this is what it takes to get a reply....Originally posted by insixdays777
To bad it hasn't got you your paid for parts...Zero Gravity Customs
Play hard or go home......
My feedback
http://www.automags.org/forums/showthread.php?t=129891Comment
-
No. But I have a frame for saleOriginally posted by Carnage reigns
Comment
-
Not a fan of that trigger and I would be collecting all my parts to later this year.Originally posted by SmoothiceNo. But I have a frame for salesigpicComment
-
It's basically modeled after a Timmy trigger with respect to the pivot point and it feels great. I'd much rather use this trigger than one made for an Intelli.Originally posted by Carnage reignsComment
-
Originally posted by G-Force Tech
Lies sir, i thought theses were off to anno, but then again i follow this thread looking for my lpr about as much as you post your venom/
Comment
-
-
Originally posted by warbeak2099
Oh he didn't give a time for the pic. He just said the machine would be ready to use by wed/thur.
This is an excerpt from "If you give a Canuck your money"So after the machine "breaks" a few more times then he'll be able to take a picture.
I'm sure the batteries in the camera won't be charged though. So after the snow storm he'll be able to go to the store.
But when he gets there they will be out of batteries...
**NO offense to any other canuck's that may be reading this post "
Comment
-
May have been asked b4 but does the 2007/08 ego grips line up with the screws for this frame? If not what grips have been known to fit.sigpicComment
-
I ordered the verticle adapter, and was told that it would ship the same time as the LPRs. The only thing I've been reading about is the LPRs, how many others ordered the vert adapter?Comment
-
Good point. I didn't order a VA, but I wonder if that's going to be the next series of delays.Originally posted by sarge40Comment
Comment