Logic Ripper EM - The Electro Solution - PreOrder

[CoolHand]

My concern is me not being able to make it function correctly.
I wanted it tuned and ready to go because I doubt my ability to do that.
I'm at a loss now.

I think our best bet here is to get BigEvil involved, seeing as he's the "Mag Whisperer" and all.

Honestly, I am somewhat miffed that a valve brand new from AGD will not function properly.

P8nt informed me that none of the new valves had the right length on/off pin in them, even though they were ordered with EMag length pins.

Who knows what else they didn't get right?

I can tell you one thing though, we are quickly approaching a time when there will be nothing left to go wrong that hasn't already.

So, by that metric, it ought not be too much longer now.

[BigEvil]

What are they doing (or not doing)? I will try my best to help out.

[p8ntbal4me]

What are they doing (or not doing)? I will try my best to help out.

Sear goes to the rear to push the on/off pin in, and it sits in the rear poss.

Like its stuck there

[going_home]

Me Happy !

Got a tracking # for the marker.

[Papa_Smurf]

Mine is sitting on the kitchen table. Thanks guys.

[CoolHand]

Huzzah!

Hopefully you guys get enough enjoyment out of them to make this whole deal worthwhile for you.

It's a long shot, I know, but at least it's over now (or very nearly so).



Well done P8nt, you're a clutch player for sure.

[Ando]

Well done P8nt, you're a clutch player for sure.

You mean a saver

[CoolHand]

Why is there always a jackass waiting in the wings?

[RFLMN1]

$950 later I get a blind non-working gun.

[BigEvil]

I have Going Home's here to check out. Not going to get to it until after Xmas though.. If I get it working I will let you know what I did.

Can someone tell me

1 - What the board settings should be

2- what the on/off pin length should be?

[CoolHand]

I have Going Home's here to check out. Not going to get to it until after Xmas though.. If I get it working I will let you know what I did.

Can someone tell me

1 - What the board settings should be

2- what the on/off pin length should be?

On/Off pin should be stock EMag length and should use the EMag X-Ring.

The dwell should end up in the range of 12-18 ms. You can set it to like 25 ms and then reduce it until the marker chuffs or refuses to fire.

The Pred boards used ~15 ms of dwell, but I don't know if the UTB will be the same or not.

$950 later I get a blind non-working gun.

Who said anything about sending out non-working guns?

Lookit, all you gotta do (after BigE finds the proper dwell setting) is program the board and go.

The blindness you are correct about, and I have profusely apologized for being unable to fulfill that part of the deal, but there is nothing I can do about it.

I could have just walked away like many people before me did, but I chose to deliver as much as I was able to.

It's not 100%, but it's a damned sight better than 0%, ya know?

Of course, that doesn't make it any less crappy for you, but sometimes reality "Toad's the Wet Sprocket" (if you catch my meaning).

[BigEvil]

I started looking at Going Home's gun yesterday. Now if I could just figure out this damn 1-button utb board

Anyway... this thing is really nice. I like it alot.

[p8ntbal4me]

I started looking at Going Home's gun yesterday. Now if I could just figure out this damn 1-button utb board

Anyway... this thing is really nice. I like it alot.

I made videos explaining how to program them with my new HD camera,.. but the videos skip on my PC and are half a gig in size.

Im going to make some new ones in a few.

[CoolHand]

Now if I could just figure out this damn 1-button utb board

Don't feel bad, it was beyond me as well.

[p8ntbal4me]

Here is 3 videos I made that will explain how to work the board. Even though I shot these videos using the VER Frame,... the board functions and programming are no different.

http://www.automags.org/forums/showthread.php?p=2747420#post2747420

Everything you need to know about the board is there. Turning On and Off,.. selecting a fire mode,... and getting into setup menus to change advanced registers.