Need some feedback on what kind of frame you would like to see me manufacture.

[NU_METAL]

If everyone wants options and versatility why not make a modular design?
You could have three parts to it ( rail / trigger guard / grip handle ) that would slide together on a dovetail type mounting system and set screws. The trigger guard would be held in place via dovetail and body/rail screw kinda like this.

Me likey vewy much

[RogueFactor]

If everyone wants options and versatility why not make a modular design?
You could have three parts to it ( rail / trigger guard / grip handle ) that would slide together on a dovetail type mounting system and set screws. The trigger guard would be held in place via dovetail and body/rail screw kinda like this.

Been working on a similar concept for a few years now. Similar in concept, not quite the same mounts.To make it all work is not so easy. Making it look good is even harder. Function and form are both important when it comes to being modular.

[Flatliner333]

I'm sure Luke could figure it out. I spent about 20 minutes on paint drawing that up just to show concept but I'm sure all the measurements aren't right.My idea is this. What if the safety was built into the trigger guard's ,the guard's would have the female part of the dovetail on the top and side. The trigger would mount in the rail,the rail has the male side of the dovetail on the bottom. The top of the grip's have female and the side of the grip has male. Slide the guard down on the grip, tighten set screw. Slide the rail from the back forward. Install trigger (there is an opening in top of guard / bottom of rail ) after mag rail,sear and body are put on - the front body screw goes up through trigger guard and ties it all together. The front of the guard would only allow the grip frame rail to slide forward so much aligning the holes. Provisions for Pnue, E-Pnue or Electro could then be worked out.

[luke]

Which I don't mind as long as there is another option besides aluminum. I love aluminim grip panels, but hate having to get them anodized or powdercoated. Something in Delrin would be nice.

I will try and make them work with standard 45 grips and offer aluminum as an option.

[luke]

[BTAutoMag]

[keiko_819]

...

[luke]

On the Micro Rock Reg from Palmers he lists the length as 2.3" I assume it is JUST the housing (Not including the threaded piece), can someone verify this for me?

[BTAutoMag]

On the Micro Rock Reg from Palmers he lists the length as 2.3" I assume it is JUST the housing (Not including the threaded piece), can someone verify this for me?

as soon as I get home I will help you on this

[hill160881]

Does this mean you are looking into a gas through LPR front grip?

[BTAutoMag]

ok here are the measurments.

dia: 0.865
lenght of body minus 1/8" npt (cant think of word) 2.222
with "1/8" npt input" 2.769
adjustment screw adds 0.343 backed ALL the way out with one thread in. about 0.113 when I feel it touch something
length from bottom of the body to the center of LP air out bung 0.575


hope this helps

[luke]

Does this mean you are looking into a gas through LPR front grip?

Currently working on the grip frame, seeing if I can fit the MRR for the sleeper.

[knownothingmags]

Currently working on the grip frame, seeing if I can fit the MRR for the sleeper.

cool, cant wait,

[luke]

ok here are the measurments.

dia: 0.865
lenght of body minus 1/8" npt (cant think of word) 2.222
with "1/8" npt input" 2.769
adjustment screw adds 0.343 backed ALL the way out with one thread in. about 0.113 when I feel it touch something
length from bottom of the body to the center of LP air out bung 0.575

BT can you get me two more dimensions?

Dimension from either the top or bottom of the regulator to centerline of the LP port coming out the side and how far the fitting sticks out the side. Thanks.

[BTAutoMag]

Dimension from either the top or bottom of the regulator to centerline of the LP port coming out the side

...read it again

how far the fitting sticks out the side.

I dont have a fitting in mine. nor do I have any around