Shes done ! Halo moded into warp ( matching ) X-mag

[kevdupuis]

I've been carrying a warp on my mag for ten years, this is something I need to try.

[NU_METAL]

NICE MINI ! must be" loud "with that little snub-freak tip
Im curious about one thing thou
Is anyone else with this set up having trouble with high rates of fire ? ( 17 an above ) with this set up ?
you know ,the once an awhile ball chop
I'm thinking it might be the microphone in these ( sound activated ) loaders needing to be closer to my bolt
Its not the level 10 , cuz if i switch back to typical/vertical feed,....its fine @ 30 bps
17bps and down ,...its fine

I dont play @ high rates of fire anyway, but just wondering if you guys have come across this ?
Nu_

[Justus]

Yes, I have. High rates of fire, via RT, Xmod or otherwise, and there seems to be some hiccups. I think the loader isn't going to be able to feed at the same rate when pushing the stack up as it is when the stack is going down.

[GEE TEE]

You could try upping the force feed but I've got a feeling it will always feed slower working against gravity. Check the spring tension in the drive cone's working ok as well

It's worth remembering you need to keep hopper from running empty, otherwise the last few balls get trapped in the feed. They need balls pushing in from below constantly to keep the feed rate going, and maintain drive cone tension between shot strings. This may also contribute to chops. Chris (from flurry) upgraded the hopper using a high output Tamiya motor, which has a better torque rating and could improve performance. The original motor can burn out when converted to warp style. I picked up a couple cheap as spares on ebay but not used them as yet. Most fields I play in UK limit you to 10bps now, so high ROF on this system is never an issue

http://www.ebay.co.uk/itm/Tamiya-JR-...item3f22e13229

[TimmyJay]

I never had a problem, but I still count my shots like nickels. 5, 10, 15... Seriously I have to budget my shots.

[Syko89]

NICE MINI ! must be" loud "with that little snub-freak tip
Im curious about one thing thou
Is anyone else with this set up having trouble with high rates of fire ? ( 17 an above ) with this set up ?
you know ,the once an awhile ball chop
I'm thinking it might be the microphone in these ( sound activated ) loaders needing to be closer to my bolt
Its not the level 10 , cuz if i switch back to typical/vertical feed,....its fine @ 30 bps
17bps and down ,...its fine

I dont play @ high rates of fire anyway, but just wondering if you guys have come across this ?
Nu_

Only chop I had was when I put it in hyper mode.

[blackdeath1k]

I never had a problem, but I still count my shots like nickels. 5, 10, 15... Seriously I have to budget my shots.

I'm not the only one!!!!!!!

[blackdeath1k]

As for the high torque motor. In the original post on doing this didn't the guy say the factory motor burnt up so he had to go to the high toque motor?

[GEE TEE]

Yes he did - hence my link to it above

Touchwood my own conversion has worked fine so far

[BigEvil]

An RF link from the gun to loader might help a lot. Simon has told me that a Halo would reliably feed at just about any angle, even through a hose from the back of a stock :o

[Syko89]

Will the rf link work with a emag?

[89raider]

i wonder if this would work well with a SCION...

[zondo]

Will the rf link work with a emag?

It's been so long now, but I wonder if the new emag board p8ntbal4me has will be able to run an rf chip.

[going_home]

Hey Larry, you going to Tunaball ?

You are in NY so you must be within driving distance.

[NU_METAL]

Trying like hell Alan :)
timing has been uncanny
Got surgury around the same time (on or after May 8th )
, now the rear end granaded in my truck so , its pretty much a day by day thing
Because you have to register ahead of time ,i would image i wont get to play anyhow :/

Hey Larry, you going to Tunaball ?

You are in NY so you must be within driving distance.