ALL about the WARP-FEED

[srrdude]

GAH!

My warp jus stopped workin last week and ive been tryin to fix it ever since! i really wanna avoid the 3 hour round trip to the proshop AGAIN to get yet another piec of equipment fixed... as im typing this (or inbetween typing i guess) im workin on it. all wires seem to be connected,and i am only running 9 volts. The funny thing is this thing just stopped workin outta no where. I had just got back from the shop where i was askin bout the sensitivity (since i had just bought the warp) and it was working. then it just stopped. i tried my microswitch, i tried the sensitiivty but nothing works. It just stopped. No smoking, no sounds, nothing. Please HELP!! i just bought a z-grip so im broke right now (i ahve 14 dollars to my name) and i really cant afford a new warp... Help me Havoc!! (by the way... can i call u the H.O. of A.O. ? :P)

[Havoc_online]

rehme warm is ok, hot is not.

StygShore I cant really tell you from just reading your post, it depends how it's built, some people just make drop in kits that connect to the current battery connector, others tap into the board.

srrdude sounds like you just have your jumpers mixed up, go over the manuel again and see if you could find a error. If your convinced that something is really wrong beyond settings, take it to someone who would know or mail it to me since We're both in Tx, it shouldnt take long.

People please dont do any mods to your warp if you dont know what you are doing. It's not hard to mess something up and end up with a broken or messed up warp. I am NOT responsible for any errors you make. The orginal purpose of this thread was to inform people without warps that were seeking information or to help people who were having trouble with thier warps, I linked the 12v mod in for the people who know what they are doing but needed somewhere to start from. If you want a mod done to it, send it to me or someone who knows what they are doing. If you DO really know what you are doing but just need a little advice or have a question, please dont post it which encourages more people to have "non-stock" warps, PM me and ask me, I'll do my best to help you out. Stock warps work AWESOME and dont need anything done to them to work right.

[srrdude]

i think the jumpers are correct..

i didnt mess with anything without referrring to the manual first. Where should the jumpers b? i have the one on the bottom to controll activation.. cuz i havent installed a microswitch in my warp yet (the even with the microswitch it wont work) and i set the other jumpers up (the left set) like the manual shows: one vertical on the far left, and one horizontal across the top 2. kinda like this [:][ ][']['] if that makes any sense... ive tried almost all jumper possibilities but maybe im doin something wrong. id hate to send it off if its something small like that... even if u are just 3 hours away.

[Havoc_online]

Hrmm.. what was wrong with the warp last time when you had to get it fixed? You say that the wries are in good shape and batteries are good, have you checked the wires going to the motor? look very closely at the board and see if any of the pins burned out on any of the componets.

*added, your jumpers sound fine so it's most likely something else.

[srrdude]

no my gun was gettin fixed.. the guy there just switched a jumper from the intellie to the sensor.. and it worked for a while but then on the way home it stopped. And could u say wat u just again in english-for-dumbies?

[Havoc_online]

check the wires going to the motor and look closely at your board. look CLOSELY to see if any of the pins that connect the componets to the board have burned out.

[srrdude]

what are the pins... which components.. and how will i know if theyre burnt out?

just a side note.. my motor works fine.. i put a nine volt againts the motor and it spun...

[srrdude]

i have identified the problem.

using a very long process of elimination i can conclude that the problem lies in the switch. thats right, the on off switch.i know this, bcuz after re-routing the wire from the battery directly to the board rather than goin thro the switch, i activated my warp. prob just bad wiring in the switch. ill keep ya updated.

[Havoc_online]

are these connecting pins in good shape on this and everything else on the board.

[Havoc_online]

LoL, for future reference, could you state that you have had aftermarket mods(on/off) done to the warp

[srrdude]

i didnt tho.

[srrdude]

next thing... now ive got it spinning... how do i get the sensor to work...

[srrdude]

oh boy.. here we go again...

that component dohickey u showed me is really really hot. help.../

[Havoc_online]

the blue dial adjusts the sensor. as for the board being hot - make sure the wiring is done properly.

(plz try and use your sig once per page, you've used your 8 times this page- not trying to be a bug, just trying to save space)

[srrdude]

its not the board itself thats hot its just that one upper left component that gets hot.