Building a Mag...

[joebob09]

im in the process of building a mag. I using a ule body witht eh body rail and a y grip trigger. For the internals im going to use a lvl 10. does the lvl 10 act as the bolt or do you need another bolt to go along with that.. what other internals do i need?.. if any.

[Toranaga]

Do you have a valve?

[joebob09]

no i do not

[Branchvillian]

You need a valve. Since you will be buying the lvl 10, you might as well get the X-Valve, because it comes stock with the lvl 10. You still need a sear, and a sear pin. You also need a barrel.

[joebob09]

what does the x vavle do exactly?

[Branchvillian]

It fires the marker. It's an RT valve, but lightened. It pushes the trigger up after every shot. The good thing is that it comes stock with the lvl-X.

[joebob09]

what other vavles are there?

[Branchvillian]

AN RT valve, but that does not come stock with the lvl 10, and it is heavier.

[joebob09]

so i can buy a x valve with the lvl 10 bolt.. how much is that?

[Branchvillian]

Check the airgun store, but I know it's a little bit over 300 dollars. Sounds like alot, but remember that it comes with a 100 dollar lvl-x kit as well.

[Colangela]

i just did the same thing... the x valve comes with the level 10, which is a bolt, yes.. it also comes with a sear, u still need a sear pin and dont forget screws..
i have the y grip and ule body i reccomend them both.. benchmark makes a nice body rail..any other questions feel free to ask me

[joebob09]

ok so buying the x valve is the best way to go then i see... and all ill need after that is the sear pin ok i think thats all ill need to know.. the barrel is no problem i got that taken care of.. oh, on the rail ill need to take that barrel lock system off right? or does the benchmark not have one?

[joebob09]

is there any place that i can get like a diagram or instrustions or something for this? i can build the body i think but the internals may be a little different...

[tonybhall]

Hey Joe,

I know you said you want to build your Mag, but if you are going to buy the x valve for $300.00, why not just get a custom ule mag from the agd store? It is a complete marker that comes with the x-valve and level 10 factory tuned and tested all for $399. The best thing is that you can add custom features for less than you can buy them for seperatly. Like the ULE Trigger pull kit for $19.00. The ULE main body is only $20. It also comes with a J&J barrel at no extra charge for the ULE Body.

You may come out better this way unless you already have several parts. I ordered mine last week and expect it to come in today. If you would like I can let you know what I think of it.

Good luck.
Bryan

[Colangela]

u have to take the barrel lock system off, its pretty self explanatory when u look at it, just inscrew the screw and it comes right off

[Dayspring]

Actually, it's more like turn the rail upside down and smack the sucker out w/ a hammer. :) Some come out easy. Some require a bigger hammer. :D

[phantomhitman]

mag parts
externals
body, rail, barrel, frame

internals
valve, sear and sear pin

other parts (depends on your setup)
vertical adpater, foregrip, gas thru grip, drop forward or asa, elbow for loader, loader, fittigns and line for air

i think that is pretty much it. i would also recomend going through agd to buy a new marker. there prices are very good.

[member#10,261]

Big Stuff:
-Barrel
-Body
-Valve
-Rail
-Triggerframe
--Vertical Adapter (optional)
--Gas Thru Grip (optional)
or
--Normal Front Grip (optional)


Little Stuff:
-Plastic Nubbin (non ULE mag)
-Barrel Twist Lock Assembly (non ULE mag)
-Front Frame Screw
-Sear Assembly
-Sear Pin
-Rail Bushing (non ULE mag)
-Field Strip Screw