Stimulation
07-01-2004, 07:15 PM
I am ready to throw a good three or four hundred bucks into my PTP MicroEmag. It is golden. I bought it for $700, here:
http://www.automags.org/forums/showthread.php?t=141181
Here is a pic of my gun:
http://www.automags.org/forums/attachment.php?attachmentid=72598&stc=1
I have already purchased this 45/45 Kiss Angel Air, and WarpFeed is my next step.
Here is the angel air:
http://www.hunt101.com/img/178889.jpg
I am going to be doing the 12V warp mod along with the on/off switch with LED. I am going to purchase an 89.00 blue warpfeed from agd.
I assume I also will need to purchase PTP's warp feed adapter:
http://store2.yimg.com/I/proteam_1780_8382201
Does this gun have an intellifeed in the frame? If it does, what will I need to do in order to connect it to the warp and all? If not, what will I need to do to have the warp fire every shot? I am sure I could rig something up.
In addition to that what else do you suggest I need Warp-wise?
Now, to my next question. The gun seems to be older (only has 1.37 software) and has an older/rarer valve, it says emag micro 2000 on it. Does this have LVL 10? It says so in the ad, but i just wanted to check. The rubber insert does seem to be gone/ removed from the bolt. Would there be any sense in upgrading the valve system. I probably will be sending it in to AGD to get the software upgraded, along with a trigger job. Should I valve them mess with the valving at all?
Other than that, what else can I upgrade? The barrel is nice, an armson rifled, yet it couldnt hurt to have a kit. I have had a mag and warp before (done the 12v mod as well), and wanted to purchase another, and stole this beauty for $700, 300 less than I dedicated to a new mag. So, I get to upgrade. Thanks for you guy's excellent advice, I appreciate it. I hope I have been an detailed as possible.
- Stim
http://www.automags.org/forums/showthread.php?t=141181
Here is a pic of my gun:
http://www.automags.org/forums/attachment.php?attachmentid=72598&stc=1
I have already purchased this 45/45 Kiss Angel Air, and WarpFeed is my next step.
Here is the angel air:
http://www.hunt101.com/img/178889.jpg
I am going to be doing the 12V warp mod along with the on/off switch with LED. I am going to purchase an 89.00 blue warpfeed from agd.
I assume I also will need to purchase PTP's warp feed adapter:
http://store2.yimg.com/I/proteam_1780_8382201
Does this gun have an intellifeed in the frame? If it does, what will I need to do in order to connect it to the warp and all? If not, what will I need to do to have the warp fire every shot? I am sure I could rig something up.
In addition to that what else do you suggest I need Warp-wise?
Now, to my next question. The gun seems to be older (only has 1.37 software) and has an older/rarer valve, it says emag micro 2000 on it. Does this have LVL 10? It says so in the ad, but i just wanted to check. The rubber insert does seem to be gone/ removed from the bolt. Would there be any sense in upgrading the valve system. I probably will be sending it in to AGD to get the software upgraded, along with a trigger job. Should I valve them mess with the valving at all?
Other than that, what else can I upgrade? The barrel is nice, an armson rifled, yet it couldnt hurt to have a kit. I have had a mag and warp before (done the 12v mod as well), and wanted to purchase another, and stole this beauty for $700, 300 less than I dedicated to a new mag. So, I get to upgrade. Thanks for you guy's excellent advice, I appreciate it. I hope I have been an detailed as possible.
- Stim