PDA

View Full Version : New Built emag.. new problems!


SpitFire1299
06-27-2005, 02:28 PM
I built an emag.. it has 3.2 software, Xvalve, and stock rt on/off..

My problem is.. when i gas it up and try to shoot it on mech its just a really hard trigger pull, and nothing happens at all... its just a huge and heavy trigger pull. Then.. on mech it just clicks.

Maybe i need to go one size carrier bigger?

Also i have an adjustable tank so im putting in like 600psi.
VFX_Fenix
06-27-2005, 02:31 PM
You need an E-Mag On/Off pin. Also, check to make sure the o-ring on the top of the On/Off assy. is seated properly since that'll make it near impossible to pull the trigger in mechanical mode.
SpitFire1299
06-27-2005, 02:35 PM
Everything is seated correctly.. i never heard of an emag pin.. :( Is there anyway i could like mod mine or something?
Maggot6
06-27-2005, 02:37 PM
I'd highly suggest you don't mod your pin, and same with AGD's warranty....
SpitFire1299
06-27-2005, 02:38 PM
I dont have a warranty though... :( :(
Maggot6
06-27-2005, 02:40 PM
I was just stating that AGD doesn't reccommend it either. Talk to Tunaman if you want to know exactly what parts etc to get, and order them from him. :)
SpitFire1299
06-27-2005, 02:41 PM
Wouldnt an emax valve have the right pin though?
Big'n slo
06-27-2005, 02:42 PM
Pin length is the diffrence. Standard Rt pin is 0.750" and the Emag pin is 0.712"
If I remeber correctly

Email Tuna, he prolly has a couple floating around
Big'n slo
06-27-2005, 02:44 PM
Wouldnt an emax valve have the right pin though?

It should but if it was used on a mech marker it was prolly changed out
SpitFire1299
06-27-2005, 02:46 PM
I measured it and it is the RT one.. Arg... i wish i could just cut it down or something for now. Im dissapointed that theres a .038 difference that wont allow me to play
Tunaman
06-27-2005, 03:54 PM
If you can measure it correctly as it looks like you can, just rub it on a file and keep checking it till it gets down to .712. ;)
SpitFire1299
06-27-2005, 04:04 PM
Cool! i did that and it worked.
BigEvil
06-27-2005, 05:20 PM
Also make sure you have the special quad oring in the top of the on off. Its a black oring that is specific to the emags.
SpitFire1299
06-27-2005, 05:54 PM
I have that too.. they should put those on rt xvalves too because its good at holding the 2 orings together.
MonsterMag
06-27-2005, 06:45 PM
I hope you were joking when you said that tuna http://www.ricoracing.netfirms.com/Smilies/uhoh2.gif
SpitFire1299
06-27-2005, 11:04 PM
Well.. i successfully did what tuna said, so i dont see whats so bad about it.. its how much for a new one anyway?? not much..
Tunaman
06-28-2005, 05:22 AM
I hope you were joking when you said that tuna http://www.ricoracing.netfirms.com/Smilies/uhoh2.gifNo. i wasn't joking. He needed to get up and running fast so that is the quick fix. Glad to see it worked .
Carbon Blue
06-28-2005, 12:39 PM
I built an emag.. it has 3.2 software, Xvalve, and stock rt on/off..

My problem is.. when i gas it up and try to shoot it on mech its just a really hard trigger pull, and nothing happens at all... its just a huge and heavy trigger pull. Then.. on mech it just clicks.

Maybe i need to go one size carrier bigger?

Also i have an adjustable tank so im putting in like 600psi.

make sure you have ATLEAST 800psi going into the gun. I have an adjustable tank for sale if you want it :)

http://www.automags.org/forums/showthread.php?t=173064