View Full Version : Weights
to anyone that can help me out here. I need weights for the following:
stock emag (w/o barrel, drop, asa, etc. just emag)[same for below]
ULE emag
Tunamag/x
SFL Emag
Micro E
If anyone can get me one, some or all of these, it would be very appreciated.
zackzel
01-05-2006, 12:02 PM
My Tunamax E-mag weighs in at 2lb 7 oz
My X-mag weighs in at 2lb 10 oz
to anyone that can help me out here. I need weights for the following:
stock emag (w/o barrel, drop, asa, etc. just emag)[same for below]
ULE emag
Tunamag/x
SFL Emag
Micro E
If anyone can get me one, some or all of these, it would be very appreciated.
Your question is alittle confusing. Tuna mag is an ALL ule Emag, not an x mag. FYI my dc viking wazs 2.5 lbs and my full ULE emag is 2.8
Your question is alittle confusing. Tuna mag is an ALL ule Emag, not an x mag. FYI my dc viking wazs 2.5 lbs and my full ULE emag is 2.8
sorry. I meant tunamag/tunamax, whichever he goes by now.
11 Bravo
01-05-2006, 03:32 PM
My Karta Emag is around 2 lbs 10 oz. (non ule rail) My Xmags weigh the same as everyone elses so I guess 2 lbs 10 0z
My Hypermag weighs in at 2 lbs or a little less.
Remington
01-05-2006, 04:47 PM
to anyone that can help me out here. I need weights for the following:
stock emag (w/o barrel, drop, asa, etc. just emag)[same for below]
ULE emag
Tunamag/x
SFL Emag
Micro E
If anyone can get me one, some or all of these, it would be very appreciated.
I just want to say that I know where you're going with this and I hate you! :p ;)
behemoth
01-05-2006, 04:48 PM
I just want to say that I know where you're going with this and I hate you! :p ;)
me too.
11 Bravo
01-05-2006, 04:53 PM
Wheres he going with it? :confused:
paint magnet
01-05-2006, 05:16 PM
Since there's no ULE standard, it would be a whole lot more helpful to post your full setup when listing weight (for example, a "ULE Emag" could mean anything from an Emag valved gun with a ULE body and stock rail and frame, to one with a ULE milled rail, X valve, frame, battery pack, etc.).
http://akaowners.org/users/files/administrator_uleemag1.jpg
there is no need to post the entire setup, considering I mean only the marker itself.
ULE E-Mag is meant to be an ALL ULE (mainbody, frame, pack, rail, valve) emag. not mix and match parts.
Xmag isnt really ULE per-se, so, just looking for the weight on that.
btw. the above pic is a 1 off, so, dont go asking for it to be reproduced ;). like what you see? Imagine what you cant see :D
[
there is no need to post the entire setup, considering I mean only the marker itself.
ULE E-Mag is meant to be an ALL ULE (mainbody, frame, pack, rail, valve) emag. not mix and match parts.
Xmag isnt really ULE per-se, so, just looking for the weight on that.
btw. the above pic is a 1 off, so, dont go asking for it to be reproduced ;). like what you see? Imagine what you cant see :D
Aside from a little milling in the grip frame, is there that much weight you can take off safely?
Aside from a little milling in the grip frame, is there that much weight you can take off safely?
aye. plenty as far as I know. there is still milling left to be done. I discovered a few additional places I can remove a bit of weight from.
Powered by vBulletin® Version 4.2.3 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.