Spydermag questions. COOLHAND, please respond!

[Lenny]

SpyderMag:

1. Can you use an old Piranha e-grip as easily as a Spyder e-grip?
2. How the kick? Little, heavy, or what?
3. Does the battery life change? Better or worse?
4. Is it worth it?
5. Will it operate on board upgrades? (lighter switch, t-board, etc.)
6. Does it lower the life of the grip frame?
7. Does it put more wear on either the gun or frame?
8. Do I need an RT valve?
9. Do I need a ULT?
10. Can I still use a Lvl. 10? Or are t-board eyes good enough for me to go back to
Lvl. 7?

Coolhand:

1. Any chance you could mod it and put it all together for me to fit your Ultimate Mech Frame, and do all the rail work needed to fit t-board eyes and your eye covers? Obviously I’ll pay you (estimate, please?), and this post is only me pondering. If everything is a yes that I want to be a yes, it’ll be a go and I’ll contact you when I get some cash.

Could I also get some pictures? I need some ideas...

Thanks everyone for your time. I did a search, but it's hard to find all of the answers.

[BigEvil]

Talk to LUKE. He is starting to offer the conversion as a service.
www.lukescustoms.com

ULT=YES
RT Valve=preferable. Any valve you can use the ULT in. Some people have success with the classic valve, some dont

Wear and tear= if the conversion is done badly, or if the dwell is set too low, you can get some bolt and sear wear. The gun will be cylcing faster, so anything that wears normally will wear faster. Mostly bumpers.

LVL10 is always preferable, but the t-board and eyes should be adequate. You can always install the lvl 10 later on.

[Automaggot68]

SpyderMag:

1. Can you use an old Piranha e-grip as easily as a Spyder e-grip?
2. How the kick? Little, heavy, or what?
3. Does the battery life change? Better or worse?
4. Is it worth it?
5. Will it operate on board upgrades? (lighter switch, t-board, etc.)
6. Does it lower the life of the grip frame?
7. Does it put more wear on either the gun or frame?
8. Do I need an RT valve?
9. Do I need a ULT?
10. Can I still use a Lvl. 10? Or are t-board eyes good enough for me to go back to
Lvl. 7?

Coolhand:

1. Any chance you could mod it and put it all together for me to fit your Ultimate Mech Frame, and do all the rail work needed to fit t-board eyes and your eye covers? Obviously I’ll pay you (estimate, please?), and this post is only me pondering. If everything is a yes that I want to be a yes, it’ll be a go and I’ll contact you when I get some cash.

Could I also get some pictures? I need some ideas...

Thanks everyone for your time. I did a search, but it's hard to find all of the answers.

First of all, the easiest way to contact Ryan is to email him at tech@logicpaintball.com

That will not be Cheap at all, and you're actually better off doing a flipped noid frame, or buying his UMF Electro frame.

1. I depends on the Grip. You might want to ask Luke, he'd probably know.
2. The kick will be the same as anymag.
3. You'd have to ask the Spydermag shooters on AO.
4. Thats all personal preference.
5. If you're building something from scratch, as that's how it sounds, then you make make anything fit, so long as there's room.
6. You'd have to ask spydermag shooters.
7. You'd have to ask spydermag shooters.
8. You dont NEED an RT Valve, but it's HIGHLY reccomended for Valve recharge
9. Yes, you're gonna need one of those is it's pancake -noid operated.
10. Yes, you can use either Lvl7, or lvl 10. It doesn't matter which, it's all preference.

Edit: Nice Post, BigEvil.

[paintballfreak90]

pm'ed you about a spydermag that i have forsale.....

aim: middielax37

[CoolHand]

Well, it's going to be a big enough PITA that I'm gonna pass on the project.

I think it is entirely possible, it's just that I don't want to do it.

I'll sell you a frame, but that's it.

You are welcome to ask LUKE if he would do the machine work and assembly.

I'm just so damned busy anymore, so I'm getting picky with the projects that I take, and I have already had one like this (it was a pain in my ***, which is why I don't want to do it again).

Anyhoo . . . . . .

Sorry I didn't have better news.