Non Auto-mag tech question..

[warpfeedmod]

I know it's not an automag but it is my backup marker, I have an older Cocker that has a Dye PMP 3-way on the front (black, but not like it matters). At any rate, the 3 o-rings on the 3-way are finally shot, and I've searched high and low and can't find them. I checked out Dye's website and store, nothing there, I sent them an email but no reply. I've checked the local pb-store and even the actionvillage store and they've got nothing. The guy at AV said I might have to just replace the 3-way, but there's nothing wrong with it aside from the fact that it's an older one that apparently they don't make o-rings for? Anyone know where I could get some?

edit: This (http://www.pbreview.com/products/reviews/968/) is the 3-way I've got except mine is black. I need the 3-orings on the ram part.

[blinky1041]

I'd say disassemble your 3-way and take it to a local hardware store. You'll probably be able to find some o-rings that work fine. Be cheaper than paying for shipping too.

[warpfeedmod]

well I checked the local Sears and Ace Hardware, all their stuff was too big, the big box stores (Lowes, Home Depot and Menards) didn't carry it either. I can't seem to find any specs on it either so I could possibly find another source.

[BigEvil]

I have my brother's cocker in a million pieces and it has the same problem. None of that Dye cocker stuff was worth the price IMO. Since it's a mech, I told him to just save his money and get a newer electro - something that he can handle and that doesnt end up apart on my work bench.

If I find anything about the orings I will pass it on. Its probably just easier to either buy a whole one off of ebay or replace the three-way. One of the many benafits to have a Palmer front end on mine is that I never have to worry about such things :-)

[SR_matt]

in all honesty the dye pneumatics suck, i have not found anyone that didnt have problems with them. it probably would be easiest if you just got a new 3 way, you can get them very cheap now and get ones that are much bettter quality like ST bomb, or a palmerrs quick switch
-matt

[warpfeedmod]

Any reccomendations as to what 3-way to get or where to get it from? I checked PB gear and although they're local to me here in Illinois they only seem to have shocktech stuff that is out of stock anyway. Is there a decent online store anyone can reccomend? I might also need a new trigger rod as well? Or does that come with the 3-way? The Dye one threads onto the trigger rod, and some I've seen just slip over the end and tighten with a set screw.

[SR_matt]

no actuator rods are noramly seperate. i dont know off hand where you can look but it might be better to get one used.

-matt

[Draken]

Bomb 3way from Shocktech (http://www.shocktechusa.com/pages/marker_parts/autococker/mp_ac_bomb3way.htm)
Timing Rod from Shocktech (http://www.shocktechusa.com/pages/marker_parts/autococker/mp_ac_timerod.htm)

Not the cheapest stuff, but you can goto badlands to pick them up if you are close to chicago

[BigEvil]

Palmers has everything you will need. Im pretty sure that the actuator rod used on the dye 3-way is different than a regular one.

http://www.palmer-pursuit.com/

[Draken]

Palmers has everything you will need. Im pretty sure that the actuator rod used on the dye 3-way is different than a regular one.

http://www.palmer-pursuit.com/

It is diffrent, has a diffrent threading. I have 2 of them in blue, but they leak also, so not really looking to sell them