sixtoes1313
03-07-2007, 09:40 AM
Figured you guys would be interested in my application of AGD tech to a WGP gun. ;)
Cocker to Warpfeed- Intellifeed
Warning-I'm not responsible for any damage done to your stuff because you damaged it attempting my mod. This is fairly easy but you will need a general tinkerer's knowledge.
I dont know if this has been done before but recently because the sound activation on a warp feed didnt work( unit was burnt out) I had to mod an autococker to accept the intellifeed system commonly used on Automag intelliframes or chimera frames. All parts can be attained at radio shack for less than $10 and for tools/parts you'll need
Soldering iron
hot glue gun
vice
drill(press works the best) and drill bit set
clothes hangar
ruler
AGD warp feed
Thin guage wire (two 12" pieces)
Momentary swtich radio shack part #- 275-1571
3/32 phone plug radio shack #- 274-289
somthing to cut clothes hangar(I used sheet metal snips and file- saw would work also)
I did this mod to a psycho ballistics lightning autococker, but any cocker with this frame should work fine.( dont know the name of the frame)
Heres what I started out with-
http://img1.putfile.com/thumb/12/34423084832.jpg (http://www.putfile.com/pic.php?img=4231024)
http://img1.putfile.com/thumb/2/5721193828.jpg (http://www.putfile.com/pic.php?img=4875182)
From this point I removed the grips and sized up the area I had to work with. I found that Behind the trigger stop was a perfectly milled area to put a compression type switch so i went out the radio shack and bought the smalled momentary pushbuttom switch they had. seen here-
http://www.radioshack.com/product/index.jsp?productId=2062546&cp=2032058.2032230.2032278&pg=2&allCount=69&fbn=Price%2FUnder+%243.99&fbc=1&fr=StorePrice%2FRSK%2F00000000%2F00000399&parentPage=family
You wll also need some wire ( any type thats relatively small in thickness will do)
and this connector to connect the wire to plug into the bottom of the warpfeed.
3/32" (2.5mm) phone plug part number- 274-289
Once you have these parts cut two pieces of wire two about 12" and solder one piece to a connector sticking out of the phone plug and the other end of that wire to a connector on the momentary swtich. Do the same for the second piece of wire except this time it will be the opposite connector. Tape the connectors where bare wire is soldered so no conductivity arrises. The end result should look like this-
http://img1.putfile.com/thumb/2/5721193561.jpg (http://www.putfile.com/pic.php?img=4875180)
Connect the wireing to the warp feed and press the swtich to make sure it works. ( make sure to have the warp feed set for intellifeed)- see this link- http://www.airgun.com/downloads/intelliwarp.pdf
Next remove the set screw in the frame (trigger stop) with an allen key through a hole provided in the rear of the frame. Once the screw is removes there should be a dimple in the under side of it. Find a drill bit thats very slightly larger than your clothes hangar rod thickness and drill a hole though the underside of the set screw. Best results obtained but wraping the screw threads in tape of cloth so not to damage the threads and putting the screw in a vice. NOTE- MAKE SURE NOT TO DRILL TOO FAR OR YOULL DAMAGE THE HEX THREADS ON THE INSIDE OF THE SCREW- if you drill these out than you cant replace the screw in the frame.
http://img1.putfile.com/thumb/2/5721194185.jpg (http://www.putfile.com/pic.php?img=4875187)
Once you get a small piece of clothes hangar rod and know it fit snugly in the set screw cut that piece of rod to length. I found the perfect length to be about a little less than half an inch.
http://img1.putfile.com/thumb/2/5721194235.jpg (http://www.putfile.com/pic.php?img=4875189)
Cocker to Warpfeed- Intellifeed
Warning-I'm not responsible for any damage done to your stuff because you damaged it attempting my mod. This is fairly easy but you will need a general tinkerer's knowledge.
I dont know if this has been done before but recently because the sound activation on a warp feed didnt work( unit was burnt out) I had to mod an autococker to accept the intellifeed system commonly used on Automag intelliframes or chimera frames. All parts can be attained at radio shack for less than $10 and for tools/parts you'll need
Soldering iron
hot glue gun
vice
drill(press works the best) and drill bit set
clothes hangar
ruler
AGD warp feed
Thin guage wire (two 12" pieces)
Momentary swtich radio shack part #- 275-1571
3/32 phone plug radio shack #- 274-289
somthing to cut clothes hangar(I used sheet metal snips and file- saw would work also)
I did this mod to a psycho ballistics lightning autococker, but any cocker with this frame should work fine.( dont know the name of the frame)
Heres what I started out with-
http://img1.putfile.com/thumb/12/34423084832.jpg (http://www.putfile.com/pic.php?img=4231024)
http://img1.putfile.com/thumb/2/5721193828.jpg (http://www.putfile.com/pic.php?img=4875182)
From this point I removed the grips and sized up the area I had to work with. I found that Behind the trigger stop was a perfectly milled area to put a compression type switch so i went out the radio shack and bought the smalled momentary pushbuttom switch they had. seen here-
http://www.radioshack.com/product/index.jsp?productId=2062546&cp=2032058.2032230.2032278&pg=2&allCount=69&fbn=Price%2FUnder+%243.99&fbc=1&fr=StorePrice%2FRSK%2F00000000%2F00000399&parentPage=family
You wll also need some wire ( any type thats relatively small in thickness will do)
and this connector to connect the wire to plug into the bottom of the warpfeed.
3/32" (2.5mm) phone plug part number- 274-289
Once you have these parts cut two pieces of wire two about 12" and solder one piece to a connector sticking out of the phone plug and the other end of that wire to a connector on the momentary swtich. Do the same for the second piece of wire except this time it will be the opposite connector. Tape the connectors where bare wire is soldered so no conductivity arrises. The end result should look like this-
http://img1.putfile.com/thumb/2/5721193561.jpg (http://www.putfile.com/pic.php?img=4875180)
Connect the wireing to the warp feed and press the swtich to make sure it works. ( make sure to have the warp feed set for intellifeed)- see this link- http://www.airgun.com/downloads/intelliwarp.pdf
Next remove the set screw in the frame (trigger stop) with an allen key through a hole provided in the rear of the frame. Once the screw is removes there should be a dimple in the under side of it. Find a drill bit thats very slightly larger than your clothes hangar rod thickness and drill a hole though the underside of the set screw. Best results obtained but wraping the screw threads in tape of cloth so not to damage the threads and putting the screw in a vice. NOTE- MAKE SURE NOT TO DRILL TOO FAR OR YOULL DAMAGE THE HEX THREADS ON THE INSIDE OF THE SCREW- if you drill these out than you cant replace the screw in the frame.
http://img1.putfile.com/thumb/2/5721194185.jpg (http://www.putfile.com/pic.php?img=4875187)
Once you get a small piece of clothes hangar rod and know it fit snugly in the set screw cut that piece of rod to length. I found the perfect length to be about a little less than half an inch.
http://img1.putfile.com/thumb/2/5721194235.jpg (http://www.putfile.com/pic.php?img=4875189)