any ideas for my pistol?

[mr doo doo]

http://i149.photobucket.com/albums/s49/mistahchao/DSC03409.jpg


aw... the BE hopper is holding me back from a mag pistoly :( anyone have any ideas on what i should do to make it like a phantom feed without spending a load on it?

jay, if this looks a lot like yours, my bad :ninja:

[Lomarandil]

Easy way, if a bit expensive... buy one of Noxx's springfeeds... cut it down to size if necessary, and either run it from the top or bottom of your powerfeed... bottom would actually look really nice..
Lo

[mr doo doo]

yea, i thought about that, and its a shame to say that its a little expensive for me, or if were to spend that much, try to make it a bit more matching.

yea, im a cheap person :argh:

[jay8541]

I think it looks good I have 3 of those same venturi barrels

First off there are many options here are a few

This is what I would do so you do not need to go machining to much,BUT it is not cheap either

get a tac one body
get a long bow mag reciever and magazines
I would convert their 21 round mag into a 10 round one ( that is me )


Or go ule vert body
put a phanton feed like system but spring powered
or use a pistol mag from a pistol like an overlord etc there are many


or you get up with someone who is willing to get a little crazy to help you design something :rolleyes: this revolving loader is still going to br finished for my personal pump mag well one of them will have it as shown is the 25 and 50 round revolver

http://i68.photobucket.com/albums/i15/jay8541/Picture460.jpghttp://i68.photobucket.com/albums/i15/jay8541/Picture459.jpg

[mr doo doo]

haha, thanks jay. WOW, that thing is crazy!

hum... the ideas are nice, but way over the top for my tastes. i really like the ULE body idea since i have seen it before, but then i dont get to use my small venturi barrel :( .

gosh, it really sucks to be be a cheap doo doo.

[jay8541]

you want cheap


take a PTP warp 90 put it on the power feed facing back wards but on an angle up
take a phanton 10 round feed tube with the back part on it then get an abs 3/4 cuplink I belive that is the size and it is black do not get a schedule 40 3/4 it will be to big then attach the ptp 90 and the feed tube with the cuplink


aslo I used a reverse valve and I put the 12 gram changer in a RT short ASA then put a double male connector between that and the valve so it was almost a direct feed with the air so I got more shots out of the co2 before changing

[olinar]

you want cheap as hell?

1.go to home depot
2.buy black pvc and necessary elbow
3.????????
4.profit

[mr doo doo]

ooohhh olinar, im like that idea....

jay, i like your idea as well too. not sure where i will get those cuplinks though ( i dont even know what they are! i googled it and got muffin pictures :confused: ) i get around 20 +/- 2 shots, how about you jay?

i have a 90* adapter, but maybe there is a way to directly attach that to a 10 round tube...

[Rudz]

your getting 20 shots? crap im only getting like 13... :mad:

[mt84]

Quote jay8541 "take a PTP warp 90 put it on the power feed facing back wards but on an angle up take a phanton 10 round feed tube with the back part on it then get an abs 3/4 cuplink I belive that is the size and it is black do not get a schedule 40 3/4 it will be to big then attach the ptp 90 and the feed tube with the cuplink"

http://i128.photobucket.com/albums/p200/mt84/mt84%20arsenal/SniperII-0503.gif

Some thing like this, PTP power feed adapter 3/4 pipe adapter and 10 rnd tube with ball stop from a Phantom.... ;)

[mr doo doo]

well rudz, you'll get there ;)

mt84, ah, i see i see. so i guess the next stop is to home depot to get some 3/4 adapters! what is that black thing wrapped around it?

[jay8541]

ooohhh olinar, im like that idea....

jay, i like your idea as well too. not sure where i will get those cuplinks though ( i dont even know what they are! i googled it and got muffin pictures :confused: ) i get around 20 +/- 2 shots, how about you jay?

i have a 90* adapter, but maybe there is a way to directly attach that to a 10 round tube...



you can get it from any plumbing supply house it is a 3/4 abs cuplink, it is a dbl female connection ask them they will know what it is

12 gram shots when i had it directly mounted to the valve and I used a level ten and not rapid fire around 20 shots as well

[mr doo doo]

yea, i figured maybe plumbing places may have them too, but the closet store to me that could have it is Home Depot. it used to be a YardBirds, but Home Depot took over :(

[buzzboy]

ooohhh olinar, im like that idea....

jay, i like your idea as well too. not sure where i will get those cuplinks though ( i dont even know what they are! i googled it and got muffin pictures :confused: ) i get around 20 +/- 2 shots, how about you jay?

i have a 90* adapter, but maybe there is a way to directly attach that to a 10 round tube...


The piece is an CPVC coupling that you want.

[mr doo doo]

cool, thanks everyone for helping me out with such a simple project. but i finally got it together using a 1/2 PVC coupling. Had to sand one of the sides a bit to fit the 90* adapter.

http://i149.photobucket.com/albums/s49/mistahchao/DSC03424.jpg

WOHOO! :cheers:

[chill will]

:clap: