My new purchaces...

[AGDlover]

Well yesterday was a Long wait for the mail but a worth while wait. I'm finaly parting my ways with my emag which has been a awsome gun for the last 3-4years. I sold my sole to the devil and traded him for....
A Martin Mini-Block autocker
System X cocker with an E2
1 68/45
1 91/45
2 Halos

http://img2.putfile.com/thumb/1/419521380.jpg (http://www.putfile.com/pic.php?img=7425598)
What Came in my box-o-goodies!
http://img2.putfile.com/thumb/1/501524853.jpg (http://www.putfile.com/pic.php?img=7427152)
Martin
http://img2.putfile.com/thumb/1/501524975.jpg (http://www.putfile.com/pic.php?img=7427154)
http://img2.putfile.com/thumb/1/501524922.jpg (http://www.putfile.com/pic.php?img=7427155)
All 3 of my baby's
Still havent Decided what I'm gonna do with the system X cocker yet. I Like that it has an E2 but it needs some changeing.... hmmm project cocker?

Click here to watch Martin-E2-mini-block (http://media.putfile.com/Martin-E2-mini-block)
Vid 1
Click here to watch Martin-E2-mini-block2 (http://media.putfile.com/Martin-E2-mini-block2)
Vid 2


P.S. ... I hate shocktech asa's....

[Ruler_Mark]

i did the opposite, you will soon regret it but although depending on your emag you might beable to part everything and buy back an emag with $$ leftover

[Scott Hudnall]

I think you lost on the deal. sorry.

[t_boneshacone]

i think you did pretty good although the market for cockers is not so hot right now, you scored two awesome cockers as far as i am concerned

[AGDlover]

I'm not worryed about the market for cockers cause I plan on owneing them as long as I can who know maybe I can pull off a trade later on but thats not an issue now. Does anyone know where I can buy a rebuild kit for thease guns, I'd hate to blow an oring somewhere down the line and not have anything for it.
Thanks

[dixieoutfitter94]

it may be the bolt in the way but that looks like a midblock....

[BigTrucker]

Check out Palmer's. The do all kinds of thingd for Cockers, even have springs and O-ring. http://www.palmer-pursuit.com/a1/

[drg]

I for one think you did good. The tanks and loaders alone are worth at least 300 bucks, the electro frames alone on the cockers are worth another 350 minimum. Martin bodies aren't very easy to get your hands on.

As for maintenance, you don't really have to worry about any of the o-rings on the cockers becoming hard to find in the future, they are all very common o-rings.

The rarest seal on the whole gun is probably the solenoid manifold seal, which can be had from airsoldier.

I'd say put the E2 on the martin ;)

Is there an mQ in your future? :clap:

[t0nnn]

www.compulsivepaintball.com

they sell a ton of cocker stuff, and have a single re-build o-ring kit or a huge o-ring kit good for 5 rebuilds.

[AGDlover]

Yeah i just put the e2 frame on the martin tonight since I did want to do it since I saw em. Swapped the boards so the e2 has the better of the 2 boards. BTW who flashes E2 boards to current software? Thanks for the compulsivepaintball link I actualy did find a coupple parts i may be looking into...

As for an MQ valve. You can deff bet I'll be looking to get one but I just gotta save some money for one! And I figure if I do get one I'll send the martin out to have it installed and tuned in correctly. :headbang: :shooting:

[drg]

What software do you have in there now? There are reasons to stick with almost any level of software, especially the ramping ones aren't too much different from each other.

[AGDlover]

Ver. 0.24

[Xadion]

PE can flash the board- at any even they have tech they should beable to do it- althought they charge something stupid like 50-80$ i check at PSP they would not quote me in email a price before hand just "They will take care of you" - 50-80$ for them to plug it into a lap top and run a prog is boo-hiss :-( but it is available