RT on off pin

[vmaxnick]

Hi
In my previous thread I was outlining the problems I have with my RT trigger
I have just stripped her again and on close examination I find the on /off pin is only .587" when I understand it should be .750" the end also feels somewhat jagged as if broken

http://s148.photobucket.com/albums/s34/vmaxnick/rt/?action=view&current=DSCF0163.jpg

Can someone please advise?

[vmaxnick]

have just made a new pin to .750" from a cobolt drill
http://s148.photobucket.com/albums/s34/vmaxnick/?action=view&current=DSCF0164.jpg

Can someone just tell me if I am right about this broken pin business before I proceed? :(

[211]

That could definitely be your problem, never heard of an on/off that short

[vmaxnick]

thanks for your reply
I have put her back together now and everything is coming up ok, no leaks, trigger is airing up
only problem now is she won't fire.
a little bit of fine tuning the on/off pin maybe?

[211]

try shortening it slightly, just a few thousandths, and try adjusting the velocity also

[211]

by the way, that new pin rocks
did you turn that on a lathe?

[vmaxnick]

Yes I did 211. I just loosened the trigger a tad and took a further .05" off the pin collar and she shoots!!!!! Wahay!
She shoots! She scores!!

Just got to make some nubbins now as mine was rusted away
anyone know for any diagrams or photos of a nubbin on the net?

[vmaxnick]

now for a really stupid question!
how do I adjust the velocity only she only shoots about 30yds?

Also I have the old type bottle reg on (Not asa) with an allen headed bolt on the end how do I adjust that and should I need to?

[211]

the end of the vlave is the velocity adjuster, turn in to go up, out to go down, should be the same with your tank reg (althought what type of tank reg do you have?)
if you turn the velocity up to high it will start to vwent out the back, this is normal just turn it down until it stops then head for a chrono
as far as the nubbins, just buy some plastic nubbins from AGD. They are much nicer on paint than the old wire nubbins

[vmaxnick]

the end of the vlave is the velocity adjuster, turn in to go up, out to go down, should be the same with your tank reg (althought what type of tank reg do you have?)
if you turn the velocity up to high it will start to vwent out the back, this is normal just turn it down until it stops then head for a chrono
as far as the nubbins, just buy some plastic nubbins from AGD. They are much nicer on paint than the old wire nubbins
Cheers mate I have just done that and she now shoots into tomorrow and straight!
Damn these guns are good!!!
I am as happy as a puppy with two ******** and a long tongue!!
I have ordered some plastic nubbins but they will take a few days so I am hoping to make some temp ones out of stainless wire if I can find out what they look like!
tank reg is tsunami
i just need to find that sweet spot now!

[211]

the higher the input psi from the tank the easier it is to sweetspot
Ill take a quick peek for a wire nubbin pic
basically
_____________________/\

[michbich]

You can probably just take a paper clip and fold it like 211 said. As long as the part holding the paint isn't sharp or too deep, you should be alright.

[211]

cant seem to find a pic of a wire nubbin anywhere :tard:
Ive even got 1 rolloing around my gear, that I cant find

[vmaxnick]

the higher the input psi from the tank the easier it is to sweetspot
Ill take a quick peek for a wire nubbin pic
basically
_____________________/\

Thanks 211
that makes sense to me actually as I had the remains of my nubbin but the rest of the U shaped bit had rusted off!
Heres some pictures from start to finish!

http://s148.photobucket.com/albums/s34/vmaxnick/rt/

[211]

Nice
euro high rise classic RT :headbang:

[michbich]

the only pic i could find was here:
http://www.automagsuk.com/classicandrt.html

[halB]

WAIT WAIT WAIT

You made a new on/off pin, and that was before you knew how to turn the velocity up!? Kudos to you good sir. THAT shows skill!

[vmaxnick]

the only pic i could find was here:
http://www.automagsuk.com/classicandrt.html
Thanks for your help guys, I've just made a nubbin from 1mm stainless mig wire and shot off a whole hopper of paint in about 15 seconds

God I love this gun!!!!

Going to go and poon me some scrap cars!! :clap: :clap: :clap: :shooting:

[vmaxnick]

WAIT WAIT WAIT

You made a new on/off pin, and that was before you knew how to turn the velocity up!? Kudos to you good sir. THAT shows skill!

I am an engineer but I am new to paintballing so while I have the skills, I need you guys for the know how!!