PDA

View Full Version : My Mags are Almost Done


Don Carnage
09-08-2008, 09:43 PM
My 2 mags are just about complete.

First my G-Force Karta Mag. I'm still waiting for an internal LPR so I can remove the ghetto set-up on the ASA. But it is shooting like a dream. My top two picks when I decided to put away the A-5 and pick up a high-end mechanical gun were the G-Force Super 68 or a Karta Automag. Neither were in production at the time. Now I have both in one. :dance:
http://i243.photobucket.com/albums/ff206/Vladruk/Homeless%20Pics/KatraG-Force.jpg

Second, my Minimag. It has a Noxx cocker adapter and had had a vertical feed-mod done by Luke's Customs. With the E-Mag pin and a 1K output NitroDuck tank, I can get the RT to burst at about 18 bps. Not too sure about the stock yet.
http://i243.photobucket.com/albums/ff206/Vladruk/Homeless%20Pics/MiniMag.jpg
http://i243.photobucket.com/albums/ff206/Vladruk/Homeless%20Pics/MiniMag2.jpg
questionful
09-09-2008, 01:18 AM
both look great. I would go about getting some custom grips on the g-force. The plain, flat stock ones don't match the karta body. But definitely cool.

How do you like the feed offset to the left? I would think as a righty (I assume, from your stock) you would want it on the right?
jade_monkey07
09-09-2008, 01:39 AM
Love the karta! How are you liking your gforce frame?
Watcher
09-09-2008, 03:02 AM
both look great. I would go about getting some custom grips on the g-force. The plain, flat stock ones don't match the karta body. But definitely cool.

How do you like the feed offset to the left? I would think as a righty (I assume, from your stock) you would want it on the right?


But then again, rightys tend to lean out the right side of cover, so a left feed leaves the hopper protected...



Nice mags man, what I woudn't give :shooting:

How did you get the threaded feedneck on that minimag body?
Don Carnage
09-09-2008, 07:55 AM
Love the karta! How are you liking your gforce frame?

The G-Force is pretty cool. But the jury is still out if I prefer it over a high-pressure RT trigger. Nothing against it, I just like the trigger bounce. Sad, I know.


How did you get the threaded feedneck on that minimag body?

It's not threaded. Just Redz Spyder feedneck bolted on it.

I was worried about the Left hopper for a while, but it's not too far to the left that it actually gets in the way. In fact it helps a little, since I naturally lean the gun to the left a little to see past a center feed hopper.
Hook
09-09-2008, 08:31 AM
Second, my Minimag. It has a Noxx cocker adapter and had had a vertical feed-mod done by Luke's Customs. With the E-Mag pin and a 1K output NitroDuck tank, I can get the RT to burst at about 18 bps. Not too sure about the stock yet.


Well, if you're unsure about the stock, I'll buy it off you in a heartbeat. LMK if you want to part with it.
Ruler_Mark
09-09-2008, 12:51 PM
thoose are 2 very nice guns. congrats
trevorjk
09-09-2008, 02:00 PM
how much was looks vert mod?
Don Carnage
09-09-2008, 08:25 PM
how much was looks vert mod?

The mod itself is $35. Black Powdercoating is an additional $25.

If you check this Link, (http://lukescustoms.com/page0027.htm) you'll find the mod prices and pics about halfway down the page. I'll gladly tell you that Luke's work is great and his turn around time is super fast