Project 03 Half Mill Viking

[tolar250]

Project 03 Half Mill Viking $165.00 Shipped SOLD

Trades:

X-Valve Spare Carriers and ULT's are a plus
Eblade E2 Kit + cash (anodized frame/chrome solenoid cover)
anything else just offer up

Airs up with no leaks comes with WAS 2.0 Board, A+ Ano Feedneck, Raw Warped Bolt Pin, Diet Milled Frame. a previous owner attempted to drilled and tapped the eye cover holes for 6-32 threads, so 4 of the 6 eye/detent cover holes will need helicoiled. i have no screws for the eye covers. comes with everything pictured. not pictured but included will be a battery harness and trigger switch once i make them up sometime this week.

6/12/13
Sorted out all the electronics last night. Made up a trigger switch, and battery pigtail. I checked the functionality of the eyes to find the ones I had were not working so I made up a new set of those as well.

6/14/13
Assembled (minus eye covers) and test fired

http://www.youtube.com/watch?v=X8cZiUxxJ1k
http://www.youtube.com/watch?v=0u-Nk74_uHE


http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_220227_zpsd00aae89.jpg
http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_220242_zps963a8947.jpg
http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_220251_zps13ee5b23.jpg
http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_220259_zps363bdb86.jpg
http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_220309_zps4a3d9073.jpg
http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_220316_zps2e37aece.jpg
http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_220341_zps6801839f.jpg
http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_220359_zps083cc274.jpg
http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_220434_zps90d3b8f3.jpg
http://i35.photobucket.com/albums/d161/tolar250/Part%20For%20Sale/20130610_231853_zpsbe082f6a.jpg

[tolar250]

Sorted out all the electronics last night. Made up a trigger switch, and battery pigtail. I checked the functionality of the eyes to find the ones I had were not working so I made up a new set of those as well. Upon double checking the eye cover mounting holes I believe it would be best to have all three on the non detent side heli-coiled along with the bottom mounting hole on the detent side. Gun is now all assembled minus eye covers and detent. I will get another picture, and try to make a dry firing video tonight.


http://www.youtube.com/watch?v=0u-Nk74_uHE

[tolar250]

Ok raised most of the money i needed to i am now open to trading for an X-Valve. Spare carriers and ULT's are a plus.

[tolar250]

would also look and Eblade E2 kits plus cash in trade

[tolar250]

would look at trading this plus cash for a VER frame

[tolar250]

still here offer up