PDA

View Full Version : stupid sear question?



blackdeath1k
07-08-2013, 11:33 PM
What is the sear pin length supposed to be on an automagRT with a Ygrip? And where exactly do I take my caliper measurement from?

I ask this because the way my gun has been set up for the last 13 years the safety has not worked. But the gun worked flawlessly. So I never adjusted the sear. I just used the pf plug as a safety. Well this coming weekend is the WRP scenario and I decided to fix the sear proper so the safety will work and I can't get in trouble. Now I have the cc gap by the trigger. But it still hit and miss fires with the safety on. But now it has other minor firing quarks. Double fires if I feather the trigger in slowly. Sputters sometimes. Ect. I'm guessing the sear is starting to get worn out? Because the bolt looks great. And I didn't think to check the sear before I put the gun back together. Its just odd it worked perfect before I adjusted the sear that was too long.

Nobody
07-09-2013, 09:48 AM
what's the safely on an electro? i wouldn't worry about the safety all that much. by turning off the flow of paint, its safer than what you where trying to fix.

take it back out, and go for reliable. what you have sounds unsafe. i think you check the length from the sear arm to the end of the threads. i don't know if its in the stickies or faq, but i'm sure that someone that has the info will be along with it.

blackdeath1k
07-09-2013, 10:18 AM
Well for now I'm gonna put it back how it was. Yes I'm always a fan of shutting off paint flow as a safety. Was just afraid if they herd the gun fire outside of the net they might get pissy. Think I'll take my chances for now. And while its apart check sear wear. And look up spec. I'm sure that one has been asked a few times. Since I was asking the other I figured I'd throw that in there also. Have a dealing my old sear has about ran its life out. We will see. Just odd that when set up not proper it has worked great for years. But try to set it up correct and it acts up. Go figure.

blackdeath1k
07-09-2013, 10:25 AM
!!!! Maybe its a tad too short now!!!!!! Gots to find the spec now.

blackdeath1k
07-09-2013, 12:11 PM
Crap! Its harder to find this spec than I thought. Time to keep looking. Anyone with the info it would be great.

blackdeath1k
07-09-2013, 12:23 PM
ok when ur setting up the trigger rod to the 1.985 inches where do u measure from.


From the end of the rod to the end of the clevis.

Found what I was looking for. I know what I'm doing tonight.

athomas
07-09-2013, 01:40 PM
When you have the gun gassed up, hold the trigger against the safety. The sear should be fully forward. This where the credit card gap comes into play. With the sear fully forward, the back of the trigger should be a credit card thickness ahead of the front of the trigger rod on the sear. This will allow the sear to fully rotate forward and open the on-off to recharge the valve. Now, when you release the safety and pull the trigger, the trigger should be able to contact the trigger rod and push it far enough back to fully release the bolt. If this happens, then that part of the gun is working properly. It doesn't really matter what the length of the rod is if you follow that spec. The actual trigger rod spec won't be accurate for all setups depending on what triggers are used and what grip frames are used, but most setups will work if you follow the idea of allowing the trigger to have a gap when pulled against the safety and able to push far enough to clear the bolt.

blackdeath1k
07-09-2013, 02:21 PM
I'm to lazy for all that crap! :D

I'll mess with it when I get home.

blackdeath1k
07-10-2013, 06:03 PM
All better. Magic number was 1.938. Sear looks borderline new. And it is NOT the carbon tip sear of the original. So for the first time since 2000 I have a fully functional safety.

While I was at it I added the 2 trigger stops. So no wiggle on the safety on side. And it hits the stop onece the trigger is pulled far enough to stop all air seepage. Good day.