Does anyone want ULE RT or Minimag, ripper, phoenix or shockwave bodies?

[Xmagterror]

Thinking of doing a run of something soon.

Does anyone what to buy a:

ULE Minimag body
http://i182.photobucket.com/albums/x291/bridgemach90/2012-05-08_13-26-24_82.jpg

ULE RT front body
http://i182.photobucket.com/albums/x291/bridgemach90/ULEEMAGRTFRONT_zpsaee647a0.jpg
ULE Classic RT body
http://i182.photobucket.com/albums/x291/bridgemach90/ULERTBODY_zpsa95edf96.jpg

ULE Classic RT body for X valve
http://i182.photobucket.com/albums/x291/bridgemach90/ULERTXVALVE_zpscfdc97d7.jpg

ULE warp minimag body
ULE warp RT front body
http://i182.photobucket.com/albums/x291/bridgemach90/2013-04-28_22-58-53_574_zps1100c934.jpg


Shockwave body
http://i182.photobucket.com/albums/x291/bridgemach90/DSC01979.jpg


Ripper body/rail
http://i182.photobucket.com/albums/x291/bridgemach90/RIPPERSIDE.jpg

Phoenix body/rail
http://i182.photobucket.com/albums/x291/bridgemach90/Combo.jpg

[Levi]

Is any of this going to be available in a warp left version? I would be interested in a warp left body for my classic RT.

[Laku]

I'd say I could be easily tempted by Phoenix body/rail. :)

[debruynda]

I'll definitely be down for a ripper or phoenix...ripper being first choice.

[astr0xz0mbie]

i would be interested in a ripper body/rail :) preferably without the feedneck so i can add my own and can you anno it ???

[vintage]

i'd like to have one for a classic valve, powerfeed, twistlock, hopper right, but oh well....

[maverick13]

I could be interested by a phoenix body/rail depanding on price ..... and time !

But didn't you mentioned a unibody project ????

[debruynda]

What price were you thinking for a ripper body?

I emailed with RPG a while back as he had a couple chord v2 bodies in stock and the only thing that turned me off was the cost, 375...a bit salty for just a body (with feedneck and detents)...but a sweet looking body but nonetheless.

[Patron God of Pirates]

Phoenix is my preference, but I would would be down for a ripper if you went that way.

[barkingspider]

Phoenix gets my vote

[Xmagterror]

I can make warp left bodies with minimag and RT front.

I will do a run of phoenix and ripper bodies with rails for both if there is enough demand...would need to sell a dozen total.
I have a few shockwave bodies instock that are ready to ship.

[kwik175]

I would be in for a Ripper if the front can be shortened to fit AM length rails. It would look nice with the new Armada rail I ordered.

[Xmagterror]

Yes i can do that for you

[BLachance75]

What about working with Luke and Panda to come up with a new body to match the Armada rails.

[Xmagterror]

I will start a preorder soon. Im thinking i will do phoenix and ripper bodies with matching rails and also a batch of ULE bodies in warp left and vert feed (both RT and minimag style fronts)....I might do some custom front designs also.


I have 2 shockwave bodies instock and ready to ship. If your guys want one you can PM me. I would need to sell atleast 10 of those to run them again. That was a very time consuming project to make the blanks and do all the milling on them.

[BLachance75]

I will most likely pick up a Minimag style body.

I would like to see a body to match the Armada rail though. Kind of like a Ripper but that follows the Armada rails lines.

[Xmagterror]

unfortunately right now i do not have the time or to take on a new project. I already have blueprints and programs from my past work. Ive had allot of inquiry's lately about bodies so i figured it was time to make some more.
Ive been working on Lamborghini parts the last few months....FUN STUFF!!!

[dodge3500]

Lol i would have to sell some stuff but a ripper body would be soo sweet.:)

[debruynda]

Lol i would have to sell some stuff but a ripper body would be soo sweet.:)

Right there with you

[RT Lover]

what feed neck is on the ripper, we need a new body a karta - xmag something like that

[Xmagterror]

thats an xmag feedneck i had years back...I put angel threads on it. Forgot who i sold that to. could always make some.

yes another all out 3D machined body design would be cool. Keith and I have been talking about it but everyones short on time and we have yet to nail down a solid design before we do the cad. A body design of that caliper is around 1200-1500 to have the cad done. creating solid g code from the cad to 3D mill the body is also time consuming. It will happen but were about 4 months away from getting something into production.

[Runamok]

I want a ule sydarm body. hint hint.

[RT Lover]

thats an xmag feedneck i had years back...I put angel threads on it. Forgot who i sold that to. could always make some.

yes another all out 3D machined body design would be cool. Keith and I have been talking about it but everyones short on time and we have yet to nail down a solid design before we do the cad. A body design of that caliper is around 1200-1500 to have the cad done. creating solid g code from the cad to 3D mill the body is also time consuming. It will happen but were about 4 months away from getting something into production.

GREAT! that puts us tax refund season! I can work with that lol! I need a feed neck like that in my body lmk

[Xmagterror]

GREAT! that puts us tax refund season! I can work with that lol! I need a feed neck like that in my body lmk

anything is possible if there is enough demand.

[rukh013]

FIRSTLY... I know this is well within your skill level but...

how hard is it to get rid of the angel treaded detents on the sides and go with a(n) ego/sypder finger detent system hidden by the rail???

instead of using milling realestate for threaded detents cut two recess areas for ego detents 15* from each other centered on the PIM

i would love a ripper AM length with some hidden detents... there are such great lines on these bodies (all of yours actually) but they are broken up by the detents

[Xmagterror]

I want a ule sydarm body. hint hint.

It almost happened....I was working on it for a while but the stacked tube design would be hard to make out of thin walled aluminum tubing and i didnt want any ugly welds on the thing.

[rukh013]

It almost happened....I was working on it for a while but the stacked tube design would be hard to make out of thin walled aluminum tubing and i didnt want any ugly welds on the thing.

http://www.mcarterbrown.com/forums/avratech/220782-retro-7-gen-iii-production-news.html

R7 style milling where the two tubes are milled into one piece...

[OPBN]

http://www.mcarterbrown.com/forums/avratech/220782-retro-7-gen-iii-production-news.html

R7 style milling where the two tubes are milled into one piece...

Might actually make me buy a Sydarm....

[BLachance75]

FIRSTLY... I know this is well within your skill level but...

how hard is it to get rid of the angel treaded detents on the sides and go with a(n) ego/sypder finger detent system hidden by the rail???

instead of using milling realestate for threaded detents cut two recess areas for ego detents 15* from each other centered on the PIM

i would love a ripper AM length with some hidden detents... there are such great lines on these bodies (all of yours actually) but they are broken up by the detents

I like this idea. I would love to see it happen if possible.

[BLachance75]

http://www.mcarterbrown.com/forums/avratech/220782-retro-7-gen-iii-production-news.html

R7 style milling where the two tubes are milled into one piece...

The R7 actually has2 tubes that bolt together. It could work for a Sydarm.

[rukh013]

The R7 actually has2 tubes that bolt together. It could work for a Sydarm.

i know but cockers have a stacked tube, it cant be to difficult...

[BLachance75]

i know but cockers have a stacked tube, it cant be to difficult...

Using 2 tubes should be less milling and have less wasted material. Which I would imagine means it is cheaper and quicker to make.

[rukh013]

FIRSTLY... I know this is well within your skill level but...

how hard is it to get rid of the angel treaded detents on the sides and go with a(n) ego/sypder finger detent system hidden by the rail???

instead of using milling realestate for threaded detents cut two recess areas for ego detents 15* from each other centered on the PIM

i would love a ripper AM length with some hidden detents... there are such great lines on these bodies (all of yours actually) but they are broken up by the detents



I like this idea. I would love to see it happen if possible.

Thank you!
I always thought the mag could be sexier with hidden detents and full bodied milling

maybe combine the "Rukh's hidden detents" with "Hills hidden eye's" :D

[rukh013]

Using 2 tubes should be less milling and have less wasted material. Which I would imagine means it is cheaper and quicker to make.

would you just put an oring in a groove between the two tubes for a seal???

OR :D

make a 12g changer fit in a grip and route the air thru the bottom of the sydearm valve

[knownothingmags]

I would like a shockwave body and rail.

[OPBN]

would you just put an oring in a groove between the two tubes for a seal???

OR :D

make a 12g changer fit in a grip and route the air thru the bottom of the sydearm valve

Or incorporate a bottom air inlet into the proposed aluminum classic style valve.....

[BTAutoMag]

you know with the ULE milling on all these rails you could actually put 1 detent UNDERNEATH a body hidden by the space in a milled rail:eek:

[rukh013]

you know with the ULE milling on all these rails you could actually put 1 detent UNDERNEATH a body hidden by the space in a milled rail:eek:

except you're forgetting the PIM that holds the body to the rail...

BT did you have a pick of the sydearm valve? top and bottom is it the same???

[rukh013]

Or incorporate a bottom air inlet into the proposed aluminum classic style valve.....

or redisgn all valves around the sydearm style and have air come from whereever you want, side/top/bottom

[Laku]

Thank you!
I always thought the mag could be sexier with hidden detents and full bodied milling

maybe combine the "Rukh's hidden detents" with "Hills hidden eye's" :D

:bounce: yes!!

[Xmagterror]

some very good thoughts on all of this. anything is possible but with the limited market for this kind of thing it would be hard to turn a profit when you spend over 40-100 hours designing, programming, doing setup, machining and testing. A ule sydarm body is totally possible but how many people would by one? Stupid me just sold my almost mint sydarm to KNW...Fail.LOL

[Xmagterror]

I would like a shockwave body and rail.

A shockwave body and rail? Yes i remember that combo. I only made one body and 2 or three rails. If i can dig the programs up its possible. from what i remember you already have a shockwave unibody...was going to say i have 2 of those that are going up for sale.

[Xmagterror]

I just posted a preorder in the dealers section.
I might make some of the xmag style feednecks if there is enough interest

[TimmyJay]

Or incorporate a bottom air inlet into the proposed aluminum classic style valve.....

YES PLEASE! And Pre-cap'd...

[RT Lover]

http://img46.imageshack.us/img46/9938/s1sq.jpg (http://imageshack.us/photo/my-images/46/s1sq.jpg/) Uploaded with ImageShack.us (http://imageshack.us)

spikes?

[captian pinky]

you may want to look into how the ccm t2 is held together for your sydarm project. ;)