PDA

View Full Version : WTB: This Automag or info on the parts used! I must have it!!! DevilMag?


str8boostn
04-17-2014, 09:32 PM
I'm looking to build or buy this mag... Or one damn near identical...

I'm not concerned with the basic stuff, just the stuff in BOLD below...


Here are the specs:
Hyperframe - Retrofitted with a mini-Morlock board (Predator 5.0 code)
Luke's Hyperframe Trigger
Luke's Hyperframe Panels - Milled for on/off switch
RT-Pro Rail - Custom cut and milled for eye covers Who/where can I have this done?
Custom Eye Covers Who/where can I have this done?
ULE Body - Cut to AM/MM length, drilled for eyes, tapped for dual detents, and custom milled with "gills" over the valve Who/where can I have this done?
Blue Breakbeam Eyes
CCM No-Rise Feedneck
CP Rail and On/Off ASA
DW Carbon Fiber 10* Foregrip
XValve, ULT, Level 10

http://i155.photobucket.com/albums/s303/str8boostn/DevilMagLeft1_zps4505578a.jpg
http://i155.photobucket.com/albums/s303/str8boostn/DevilMagRight1_zps67c0faf7.jpg
http://i155.photobucket.com/albums/s303/str8boostn/DevilMag2Left2_zps008921ec.jpg
correia3
04-17-2014, 10:09 PM
If you are going the DIY route, I have the Morlock Predator board. I think mine is Predator 10 code. Not sure what the difference is compared to the 5 code board.
correia3
04-17-2014, 10:12 PM
Also - check with luke for his parts and all of the custom milling - he is your best option for all of it. I think those eye covers were p8ntbal4me products but luke does hidden eye milling on ULE bodies which would be a cleaner looking solution, IMO.
str8boostn
04-17-2014, 10:23 PM
If you are going the DIY route, I have the Morlock Predator board. I think mine is Predator 10 code. Not sure what the difference is compared to the 5 code board.
Sweet... I'll shoot you a message then!

Also - check with luke for his parts and all of the custom milling - he is your best option for all of it. I think those eye covers were p8ntbal4me products but luke does hidden eye milling on ULE bodies which would be a cleaner looking solution, IMO.
I've looked through all of his rail millings and didn't see one similar to this and I don't see anywhere, where he mills down the length of the ULE bodies or does any venting near the xvalve... But I'll give him a shout and see what he says. As for the eye covers... Either way would be cool with me!
knownothingmags
04-17-2014, 10:41 PM
I have a hyperframe. with 20bps board in it. I know you don't need the board.
but that's what I have for you.
I have a venomous designs carbon fiber forgrip.

if I recall these were rather expensive markers to put together.

good luck though.:headbang:
str8boostn
04-17-2014, 11:02 PM
I have a hyperframe. with 20bps board in it. I know you don't need the board.
but that's what I have for you.
I have a venomous designs carbon fiber forgrip.

if I recall these were rather expensive markers to put together.

good luck though.:headbang:

Pm'd
Sk8ermog
04-18-2014, 01:44 PM
What KNM you are willing to sell your hyperframe already? :(

Str8boostn: I have a hyperframe with a senerio dreams board in it that can take eyes. I might be willing to sell. Here is s PIC

http://m8.i.pbase.com/g9/15/525015/2/155192198.Sj7PEIH5.jpg

I also have about 5+ other hyperframes available if you are linking to build from scratch.

Also Luke would be the guy to talk to about any of the milling you are looking for.