Angled vertical ASA adapters (where are they?)

[Tachiro]

Is it just me or have these been curiously hard to come by these days? Anyone seen any lately or know where some are being sold? I was going to put up a WTB thread, but i figured this would make more sense to post here if anyone happens know what's going on.

[SummaryJudgement]

For automags? I haven't seen any in a while now that you mention it, but I haven't been looking myself. Autococker-wise Ebay has a fair amount right now I believe.

[knownothingmags]

OPBN might have one,
yeah the adapters luke makes them.

[going_home]

http://www.lukescustoms.com/rt-pro-foregrip.html

[alpha_q_up23]

If you're not looking to make the foregrip into a gas through, there are these
http://pages.ebay.com/link/?nav=item.view&id=301802656897&alt=web

I did have to sand down the little nub on it to fit on one of my mag rails that wasn't drilled for an Rt foregrip/slot milled, if you want I can try to post a picture of how it is on my setup later

[N3D]

If you're not looking to make the foregrip into a gas through, there are these
http://pages.ebay.com/link/?nav=item.view&id=301802656897&alt=web

I did have to sand down the little nub on it to fit on one of my mag rails that wasn't drilled for an Rt foregrip/slot milled, if you want I can try to post a picture of how it is on my setup later

this is what i plan to use after i have my emag rail milled

[Tachiro]

If you're not looking to make the foregrip into a gas through, there are these
http://pages.ebay.com/link/?nav=item.view&id=301802656897&alt=web

I did have to sand down the little nub on it to fit on one of my mag rails that wasn't drilled for an Rt foregrip/slot milled, if you want I can try to post a picture of how it is on my setup later

just bought one of those in black:
92143

i'll have to do some drill/thread tapping at an angle to get it to look/work the way i want, but that's nothing a drill press can't handle.

[OPBN]

OPBN might have one,
.
No he doesn't. Sold it a couple of months back for $60. I do believe Doc was still making them in raw, but not sure if he still is or not.

[cougar20th]

If you're not looking to make the foregrip into a gas through, there are these
http://pages.ebay.com/link/?nav=item.view&id=301802656897&alt=web

I did have to sand down the little nub on it to fit on one of my mag rails that wasn't drilled for an Rt foregrip/slot milled, if you want I can try to post a picture of how it is on my setup later

Been running one of those on my pumpmag for the last 15 years. Long before anyone was making 15* VA's for automags. Works great. On mine I cut the pin off. If I were to do it again I would likely drill a small hole in the rail or my case pumpkit.
http://i1209.photobucket.com/albums/cc395/Cougar20th/My%20PB%20Guns/P1010274_zpscd72dbc9.jpg

[OPBN]

Been running one of those on my pumpmag for the last 15 years. Long before anyone was making 15* VA's for automags. Works great. On mine I cut the pin off. If I were to do it again I would likely drill a small hole in the rail or my case pumpkit.
http://i1209.photobucket.com/albums/cc395/Cougar20th/My%20PB%20Guns/P1010274_zpscd72dbc9.jpg

That marker is still hot...

[Paint-Fool]

I think I have a black one somewhere. Never really liked it.