PDA

View Full Version : AGD PowerHouse Regulator now available.



Sandman
10-24-2019, 11:56 AM
What happens when the absolute quality Automag meets the absolute quality regulator? You get the Airgun Designs powerhouse regulator! Powerhouse regulators have shown the paintball industry how a quality regulator should act and how one should be built. Now AGD has added Powerhouse to their house with the Haymkr regulator built for AGD specs. The AGD version outputs a solid 850 psi of pressure to energize your Automag with the most consistent supply of air pressure it needs. This regulator will work with any Automag version you use. Built with a stainless threaded cartridge you now can own a regulator that will last right along side your Automag. Does not come with a tank. Requires a 4500 psi tested air tank to thread onto. Comes with great support from Powerhouse. Available now on the website.

101219

going_home
10-25-2019, 03:11 PM
Wished I had known you were up to this.

I would have waited to get one.

Much rather represent AGD....

Nobody
10-30-2019, 12:02 PM
Interesting, are these player rebuildable?
Can these be adjusted, in limited capacity, i.e. 650psi to 950psi?
Would these be able to come with different annodized bonnets?
Is there a chance for a non-stainless steel option?

Xyxyll
10-30-2019, 12:32 PM
Interesting, are these player rebuildable?
Can these be adjusted, in limited capacity, i.e. 650psi to 950psi?
Would these be able to come with different annodized bonnets?
Is there a chance for a non-stainless steel option?
While I wouldn't recommend a non-stainless steel thread cap for these regs, I suspect the Aerolite Pro reg caps may work with these. I don't have a gen III reg to compare to, but I believe the geometry for this part didn't change between gen II (Aerolite Pro) and gen III (AGD).

Red - https://www.ansgear.com/HK_Army_Aerolite_Pro_Regulator_Threaded_Cap_Red_p/hkarmytankregprotc-red.htm
Black - https://www.ansgear.com/HK_Army_Aerolite_Pro_Regulator_Threaded_Cap_Blac_p/hkarmytankregprotc-black.htm
Gold - https://www.ansgear.com/HK_Army_Aerolite_Pro_Regulator_Threaded_Cap_Gold_p/hkarmytankregprotc-gold.htm

captian pinky
10-30-2019, 03:57 PM
I think the first release will be set to 850. I originally asked about this on the gen1. I think there is a little bit more involved than just adding a shim or swapping a piston for the higher pressures. I know they are looking at it though.

Bunny
11-01-2019, 08:52 AM
Awesome work!! It would go great with my Carl Bonta E-mag :p

AGDRetro
11-02-2019, 05:51 PM
My project X-Mag needs a tank, this might be it...

koleah
07-04-2020, 07:18 PM
How does this compare against the AGD Flatline regulator? Is this just a screw-in version of the Flatline?

dstud2000
07-06-2020, 06:25 PM
No it’s a reg from Powerhouse built to AGD spec with a 850 psi output. I have one and it’s great [emoji106]

https://uploads.tapatalk-cdn.com/20200706/3897818ca67c837f009df78ed1ba36f2.jpg


Sent from my iPhone using Tapatalk

Billz804
07-07-2020, 08:14 AM
Any chance we see another run of these, Sandman?

jarhead86
07-16-2020, 11:08 AM
I’m hoping for another shot too one day