View Full Version : Intelli-warp hook up
Flip540
08-25-2001, 04:39 PM
i went to radio shack today and got all the parts need to do the thing when you pull the trigger your warp spins. well i put everything thing together and the warp keeps spinning. i thing the problem is that i didnt buy a NC conductor.they were out of those so i just bought the non nc one. can someone who knows please help me?
------------------
Flip Out
Mini Mag (soon to be powderd red)
10" red cp
AGD Blade IntelliFrame
12v Revvy
Clear AGD Warp Feed
VL Fore Grip
Max Attack 68/45
For Sale...
ss remote
stock minimag barrel
4+1 pack
"I may rock, but im not made of stone"
Humm, not sure what the problem is here. I am assuming NC means your switch is Normally Closed which would make the warp spin all the time. Most switches have three poles to connect wires too. One is common, hook one wire there, the other two are NC and NO try each combo to see which one works. Make sure you set the jumper on the right to the top position.
AGD
When you pull the trigger, does the warp stop? If it's the switch, it should. Like Tom said try different configurations on your switch.
If it still spins and your jumper is correct, you may have a short on your lines.
Hope this helps
Flip540
08-25-2001, 11:18 PM
it should look like this right
[..]
..
[..]
i followed the instruction in the post dryice made in the historic forum
------------------
Flip Out
Mini Mag (soon to be powderd red)
10" red cp
AGD Blade IntelliFrame
12v Revvy
Clear AGD Warp Feed
VL Fore Grip
Max Attack 68/45
For Sale...
ss remote
stock minimag barrel
4+1 pack
"I may rock, but im not made of stone"
DryIce
08-25-2001, 11:46 PM
Yeah, thats how it should look... But im wondering about the switch you got
hmm
------------------
http://www.galaxy-pc.com/mag <---my automag
http://www.galaxy-pc.com/mag/wiringdiagram.jpg <--- Warpfeed Intellifeed diagram
Flip540
08-25-2001, 11:51 PM
it look just like the one in the pic. it doesnt say NC on the package though. there was one that said nc on it but the one was huge and not for this.
------------------
Flip Out
Mini Mag (soon to be powderd red)
10" red cp
AGD Blade IntelliFrame
12v Revvy
Clear AGD Warp Feed
VL Fore Grip
Max Attack 68/45
For Sale...
ss remote
stock minimag barrel
4+1 pack
"I may rock, but im not made of stone"
Flip540
08-25-2001, 11:52 PM
part #274-245
------------------
Flip Out
Mini Mag (soon to be powderd red)
10" red cp
AGD Blade IntelliFrame
12v Revvy
Clear AGD Warp Feed
VL Fore Grip
Max Attack 68/45
For Sale...
ss remote
stock minimag barrel
4+1 pack
"I may rock, but im not made of stone"
Flip540
08-26-2001, 12:05 AM
hmm...i tried every combo with the wires inside the grip...the warp just spins comtinuosly(sp?). if i know me as well as i think i know me, i am prolly looking over the ssmallest thing that can be fixed with a quick pinch.
------------------
Flip Out
Mini Mag (soon to be powderd red)
10" red cp
AGD Blade IntelliFrame
12v Revvy
Clear AGD Warp Feed
VL Fore Grip
Max Attack 68/45
For Sale...
ss remote
stock minimag barrel
4+1 pack
"I may rock, but im not made of stone"
Flip.
Disconnect the wires from the switch and touch them together and see if it works. Likely you have some wires crossed, maybe in the phone jack.
AGD
BlackVCG
08-27-2001, 12:00 AM
I don't think you have the right switch. I have some of the standard switches with and with out the roller and the one with the roller that you need to use in the Intelliframe is part # 275-017A The switch w/o the roller is part # 275-016A
On the package for the roller switch, it will say: SPDT Submini Roller Lever Switch. Make sure this is what you have. All Radio Shacks should have this part and if the one you are going to does not, try a different one.
Flip540
08-27-2001, 12:18 AM
hey black i got the one with the roller. part #275-017A, im looking at the package now. the only thing i got different is the phone jack. instead of getting 274-247 i got 274-245. its the same thing i just do think that its a NC jack...?
------------------
Flip Out
Mini Mag (soon to be powderd red)
10" red cp
AGD Blade IntelliFrame
12v Revvy
Clear AGD Warp Feed
VL Fore Grip
Max Attack 68/45
For Sale...
ss remote
stock minimag barrel
4+1 pack
"I may rock, but im not made of stone"
"If its not part of the sulution, Its part of the problem"
Bad Dave
09-07-2001, 09:02 AM
do u just balance the switch under the sear to get it to work?
Dubstar112
09-07-2001, 05:07 PM
http://www.hunting-pictures.com/members/Dubstar112/grip%20inteli%20jpg.jpg
http://www.hunting-pictures.com/members/Dubstar112/grip%20inteli2%20jpg.jpg
i went through alot of trouble doing this my self also,
IM me on AOL at Teamcolors30 if you have any questions
Bad Dave
09-08-2001, 04:22 AM
how would that work on a z grip?
Dubstar112
09-08-2001, 10:59 AM
I believe Black has his zgrip with a micro switch in it to work the same. ask him for pics or do a search!
Deadpool3
09-09-2001, 09:01 AM
how do you have a AGD Blade intelliframe (i really want one)? I thought they werent selling them yet. Where you get yours?
BlackVCG
09-09-2001, 01:44 PM
Bad Dave- Look at this thread. There's also a link in this thread that goes to another thread with Z-Grip intellifeed info.
http://www.automags.org/forums/showthread.php?s=&threadid=8747&highlight=ZGrip+Intellifeed
Powered by vBulletin® Version 4.2.3 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.