Results 1 to 18 of 18

Thread: New ninja SL90 tank (2022 hydro date) and adjustable Max Flow reg

  1. #1
    Join Date
    Nov 2015
    Posts
    14

    New ninja SL90 tank (2022 hydro date) and adjustable Max Flow reg

    Sold!
    Last edited by hathegkla; 09-18-2017 at 09:28 PM.

  2. #2
    Join Date
    Apr 2010
    Location
    SODAK
    Posts
    4,795
    max flow works?

  3. #3
    Join Date
    Nov 2015
    Posts
    14
    Quote Originally Posted by knownothingmags View Post
    max flow works?
    yes, I tested it out on my mag and got it to RT at different pressures before I took it off. I think there was a slight leak at the on/off, new o-rings would probably fix that.

  4. #4
    Join Date
    Apr 2010
    Location
    SODAK
    Posts
    4,795
    Take 40$for it?

    Sent from my SM-G930V using Tapatalk

  5. #5
    Join Date
    Nov 2015
    Posts
    14
    Quote Originally Posted by knownothingmags View Post
    Take 40$for it?

    Sent from my SM-G930V using Tapatalk
    I can do $45, I can't go any lower because shipping is going to cost me at least $10.

  6. #6
    Join Date
    Apr 2010
    Location
    SODAK
    Posts
    4,795
    Quote Originally Posted by hathegkla View Post
    I can do $45, I can't go any lower because shipping is going to cost me at least $10.
    Thankyou for the counter offer but I'll have to pass

    Sent from my SM-G930V using Tapatalk

  7. #7
    Join Date
    Jan 2001
    Location
    Cottonwood, Az.
    Posts
    8,183
    Do you have a rebuild diagram for the reg? I'm curious about the design before I decide if I'm interested. Is this the MF-I reg?

  8. #8
    Join Date
    Nov 2015
    Posts
    14
    Quote Originally Posted by luke View Post
    Do you have a rebuild diagram for the reg? I'm curious about the design before I decide if I'm interested. Is this the MF-I reg?
    I'll check on that when I get home. I still have the original box so it should have the exact model info. I know it comes with an extra spring for low and high pressure.

  9. #9
    Join Date
    Jan 2001
    Location
    Cottonwood, Az.
    Posts
    8,183
    So is it a preset high or low or is it adjustable in those ranges?

  10. #10
    Join Date
    Nov 2015
    Posts
    14
    Quote Originally Posted by luke View Post
    So is it a preset high or low or is it adjustable in those ranges?
    it's adjustable within those ranges, you just turn the end cap to adjust pressure. I don't know a lot about it but it has a high and low pressure spring. I ran it over 800psi with the high pressure but I'm not sure what the limit is. I might even have the manual, I will check.

  11. #11
    Join Date
    Feb 2007
    Location
    Fredericksburg, VA
    Posts
    1,465
    Quote Originally Posted by luke View Post
    Do you have a rebuild diagram for the reg? I'm curious about the design before I decide if I'm interested. Is this the MF-I reg?
    ZDSPD has a full write-up on his site.

    http://www.zdspb.com/tech/mguide/regs/main_inline.html

    As for the output psi, if it's anything like the other Max-Flo regulators, each spring give you a different range. If you install the low pressure spring, then you use the front knob to adjust from 0-500 psi, or something like that. Or you can use the high pressure spring to adjust from 500-1000.

    You can actually also use the high pressure spring for lower pressures than 500, but it's harder to get precision adjustments in those ranges.

    Quote Originally Posted by hathegkla View Post
    yes, I tested it out on my mag and got it to RT at different pressures before I took it off. I think there was a slight leak at the on/off, new o-rings would probably fix that.
    Yeah, o-rings should fix that, but can you tell us if this regulator bleeds when shut off? If it doesn't, then it can be really hard to remove the air lines after turning the air off....unless the on/off leaks out the pressure.
    Last edited by rawbutter; 09-01-2017 at 02:55 PM.

  12. #12
    Join Date
    Jan 2001
    Location
    Cottonwood, Az.
    Posts
    8,183
    I've already imported that ZDSPD file, my CAD program had fits with it so I haven't fully explored it. lol

  13. #13
    Join Date
    Nov 2015
    Posts
    14
    Quote Originally Posted by rawbutter View Post

    Yeah, o-rings should fix that, but can you tell us if this regulator bleeds when shut off? If it doesn't, then it can be really hard to remove the air lines after turning the air off....unless the on/off leaks out the pressure.
    I'm not sure if it does. I think I just turned the tank off and fired a shot before I removed the air line. the tank is empty at this point anyway.


    EDIT: I updated the pictures and added the box info.
    Last edited by hathegkla; 09-01-2017 at 08:59 PM.

  14. #14
    Join Date
    Oct 2016
    Posts
    28
    Ill take the Max Flo if still available

    Sent from my LG-H901 using Tapatalk

  15. #15
    Join Date
    Jan 2001
    Location
    Cottonwood, Az.
    Posts
    8,183
    (I'm not in line)

  16. #16
    Join Date
    Oct 2004
    Location
    Mt. Pleasant, SC
    Posts
    2,741
    those on/offs are notorious for leaking in the inline maxflos btw.

  17. #17
    Join Date
    Dec 2011
    Posts
    92
    Pming

  18. #18
    Join Date
    Dec 2011
    Posts
    92
    Pm'ed again let me know if you aren't getting them please. I am interested in getting this.
    -Duncan

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •