Ace'd Emag is Done

[BajaBoy]

ahh ive been working on this for a wile now.. only thing that it needs to shoot is new softwear (it have 1.37 right now)

things to come.. Barrel kit, Rougefeedneck and new detents.
Then sent off to ano.. im thinking a high polished blueish pewter.

what barrel kit do you think would go good?

[BajaBoy]

..

[BajaBoy]

3..

[BajaBoy]

......

[BajaBoy]

last for now.. ill take a pic of the whole gun together later

[MicroMiniMe]

Very nice, and cleanly done to boot.
Kudos.

[paintballbeaver]

oooooohhhh sooo coooool i wanna do

ace board droool

hey i seen you haveit wired into the jumper what pin?
and then on the board? (i'm looking for info how to wire it my self care to share

[Schnitzel]

very clean...i knew it was only a matter of time before somebody did it. looks very good.

it also looks like you might have had to modify the ULE body pem, am i correct?

and wiring it correctly to that jumper must have been fun. i know from experience that those suckers are tough. looks like your timing was pretty good too with the 3.0 release pending so close and all. you might only have to wait a few weeks to acutally test it out.

i noticed the yellow pin is in there too. and you even got the power switch onto the board as well....is that prewired from AGD or did that require some special wiring as well?

[BajaBoy]

Originally posted by Schnitzel
very clean...i knew it was only a matter of time before somebody did it. looks very good.

it also looks like you might have had to modify the ULE body pem, am i correct?

and wiring it correctly to that jumper must have been fun. i know from experience that those suckers are tough. looks like your timing was pretty good too with the 3.0 release pending so close and all. you might only have to wait a few weeks to acutally test it out.

i noticed the yellow pin is in there too. and you even got the power switch onto the board as well....is that prewired from AGD or did that require some special wiring as well?

the orange wire that went into the jumper just clips in bro i thought i was in for alot more haha..

the ule frame.. yes the hole is off and i havent gotten around to doing that yet

the switch Does work, but it didnt come with the little extender spring so it doesnt stick out far enouph to use. (need to get that spring)

hmm wiring the gun was pretty easy it only involved soddering 2 wires and popping the 3rd one in place.

this project was.. well uh it can get on your nerves and i dont think anyone should take it up without a mill, thats the only reason i got it done so clean.

oh and thanx guys

What barrel system should i get?!

[BajaBoy]

oh Jeez! i forgot

people who i give credit to!

RogueFactor (for milling the rail into "ule")
ah137 (helping me get this thing going)
fire1811 (for the ace tech pix)

[Schnitzel]

you may want to talk to rogue about hiw WGP Kaner barrel kits...they're very reasonably priced for what you get.

[BajaBoy]

i think im getting a 2pc Cp barrel with 2 backs.. its cheap

[Dueydog]

CP is best according to Havon online

I asked the same question at Dallas AO meet.
Good luck,
Matt

[PevsBalla89]

Woot! Gravity Represent!
Dave is my uncle, who is this?
Nice job on the mod

[mh53eplt]

I am planning on doing your mod on both my Emax and PTP Micro 2000 and both are being upgraded to 3.2 by Tunaman. Where can one by the ace board. I checked the AGDE site and they only offer converting ones emag to an xmag. They do not sell the board seperately.