Will you be selling entire setups including the UEF? What will they cost?
Will you be selling entire setups including the UEF? What will they cost?
Z-man - "I would say we are not so much proud as...viscously loyal. Dissing AGD in earshot of AO is like throwing rocks at a bees nest... a big bees nest... with millions of freaking bees that have modded AI software, maneuverability upgrades and rocket launchers."
the Best Page in the Universe
My Ebay Feedback
My Feedback
$950 + shipping. ULE body, eyes installed, no barrel.Originally Posted by scrumpy
Ryan Shanks
Logic Industries LLC
how do you adjust the trigger pull on the gun and what is the maintnece with the lpr
Three set screws in the trigger itself. All accessible from outside the marker.Originally Posted by UDO
The ANS reg will be fine with just a few drops of oil in the ASA every once in a while. Basically the same as the Mag valve.
so.... um... when do i get to beta test the frame!!! lol
Come to the AO Missouri day and you can play a game or two with it.Originally Posted by RTspag
I'll have it there with me, as well as a Classic with my new Mech frame.
And my FreeFlow (which no one but me uses), and my Viking, and various and sundry pumps, and maybe even a slingshot.
i got dibs on the slingshot
You know, I actually went and dug mine out from eons ago, but the damned rubber tubes were rotten, so the thing kind blew up in my face when I went to do a test fire.Originally Posted by RTspag
Alas, no slingshot this time.
I think the coolness of the ElectroMag ( ) and the super comfy new Mech Mag will overcome any sorrow that folks may feel about the demise of the slingshot.
coolhand
i own a emag. i have it set up with a rear stock, i am a scenario player, the one special ops sells on the long bow, what would it cost me to have you install it to the emag rail.i also have a smart parts lpr in black.thank you verry much
I'd imagine you'd simply buy the frame for $425 since you already have the lpr. If you want him to install it along with eyes, eye covers, and ULE milling on your rail, it would be an extra $125. So, with your own SP lpr, it would come to $550. You could probably get around $300 on the classifieds section for your Emag lowers sans rail if you have 3.2 software. So, you'd be able to swap this frame in for a gross total of about $250.
I am not Coolhand, just giving an estimate. Am I right Ryan?
If we wanted to get the minimaxflo option....would we have a choice in picking out a color or will there be a standard color (black)?
Warbeak pretty much nailed it.Originally Posted by yogi
The stock has no effect on the price of the kit. If it will fit your EMag rail now, it should fit it after it is machined as well. Last I saw, the longbow kit mounted off the back sight rail holes, if that is still the case, you will want to keep your rail and let me machine it, instead of popping for a new one (as I only provide AGD slugs which have no holes in them at all).
You should be able to bolt it on yourself.
B&R - Go check the order page, I've updated it to reflect the options now offered.
How many have been ordered so far?
Ten.Originally Posted by 11 Bravo
Does this frame only work with the X-valve or can it also work with stock automags. I know it doesn't work with bodys with twist lock barrels but are there bodys that have powerfeeds that aren't twist lock?
The only powerfeed bodies there are, also take twist lock barrels, so they are out.Originally Posted by frogoa
I have not tested this frame using a classic valve, since they start to shoot down at @16bps, but I can if you think you'd like to run one I'll give it a look. You just won't be able to use the frame to its fullest.
So how light can the trigger be adjusted? What about pull length?
Did you read the first post? This is an electronic frame, IE the only weight that has to be there trigger pull wise is the microswitch, which takes 25 grams of force to actuate (The ULT takes 15ozs of force, or 425 grams of force to actuate). You can adjust the magnetic trigger return force to suit your taste, from totally slack to snappy and crisp, all from the outside of the frame.Originally Posted by splat15k
Pull length, once again, is the same situation as the pull weight. The only length that has to be there is the ~0.020" that the microswitch needs to move to actually be actuated. The trigger is totally adjustable though, so you can make the pull as long or short as you like, once again, all from outside the frame.
can it go full auto or 3 shot burst
Originally Posted by CoolHand
Yes it can. It has the Predator board.Originally Posted by frogoa
What he said.Originally Posted by 11 Bravo
i have a morlock, rail milled for eyes, and an x valve with ult. how much will it cost me to get an empty trigger frame, and my body milled for eyes?
Originally Posted by mr.mag218
It's going to take little more than JUST a board to power the fram, dude.
I'll sell you a kit without any electronics for $350, but I will not warranty it at all. If you're OK with that, so am I. (And it's not like I won't know which one I didn't assemble ).Originally Posted by mr.mag218
Add $45 if you want me to drill the body for eyes (though if you've already machined the rail, it begs the question ---> Why can't you drill the body yourself?).
How Much Would It Cost If I Already Have Xvalve And Ule Body But Want Eyes And All The Other Goodies
Frame Kit - $450Originally Posted by UDO
Slug Rail - $50
Eye Install/Rail Milling - $125
RTP Sear & Axle Assembly - $35
Rail Bushing - $1
Bike ForeGrip - $16
Macro Fittings and Line - $18 (If you want braided SS it will cost extra)
AKA Clamping Feed - $25
Shipping - $15
Total Anodized, Assembled, and Tuned - $735
No barrel, or bottom line ASA.
Registered User
Don't forget the LPROriginally Posted by CoolHand
is it possible that you could use a std jds lpr?
embargo backwards = o grab me
"Guns dont kill people, husbands that come home early do." -Larry The Cable Guy
Dragun Drallion, nexus kit, tickler, e2, pysco 5" drop w/ on off, macroline, A+ bolt and back block, Oydessy 3 barrel kit, armson stealth, 15* ASA, Kapp pump arm, Black Magic, warp feed w/ 12v upgrade, halo b w/ vic&rip, 91/4500 bulldog
Tippmann 98C ebolt, lp kit, m-16 kit, palmer stabilizer
That is correct sir.Originally Posted by SpecialBlend2786
Didn't forget it, an ANS LPR is included in the $450 kit.Originally Posted by Emag2005
If STD makes a 'cocker type LPR that will thread into an 1/8" NPT port, then yes. Otherwise, no. I know AKA makes SCM's that will work, but I don't think STD has one like that yet.Originally Posted by UTDragun
The solenoids came in today.
That just leaves ano and boards standing in the way of assembly and shipment to a grateful world.
I'm thinking they will go off to ano next week (unless the new ano guys are horribly slow on the samples).
At any rate, hopefully World Cup goes well for TAG and they have my boards for me when they said they would.
Wouldn't that be wonderful? A project that is actually running on schedule.
I was begining to wonder if such a thing were even possible.
Registered User