Old School "Magger"

[EclipseClassic]

The pin oring looks pretty yellow, maybe it just got old.

It happens to all of us...

The pin oring is old, can I replace that with a teflon, that the only replacement I have that will fit?

[djellum]

I had no idea there were so many active mag lovers. Go into a PB store and you'd think AGD was dead!

I will take some snapshots of my old mag and valve. For those of you who have been around for a while. you will be amazed by some of the stuff I paid to have done.

I ended up buying the intelliframe with the pneumag modification built into it for $125. All I have to do is get a LPR for like 40 bucks and boom I have the pnuemag trigger. I think once I hook that up to my stock body and rail with an xvalve and my smartparts barrel that I should have a pretty functional gun. The only thing is that I don't know how to hookup the low pressure regulator to the air supply. If anyone can point me in the right direction I would really appreciate it.

Is anyone here from the Seattle area?

Depends on where you want it. The 2 easiest imo are to T-off the nomal valve input and put the lpr there or get an ASA that has 2 ports and mount it below the grip. other than that your limited by imagination and budget. I know some ppl have mounted them inside the grip if theres room or on front like an AC.

I live in Vancouver (WA, no Canada). If we have any big games in my area that are worth the drive I'll let you know.

[pump]

When gassed up the valve doesn't let the air and recharge the gun. Basically it recharges in slow motion and it will chuff once and then slowly recharge for about a second or two, then I can chuff once more. It has brand new orings, I don't know what else to do. I remember it working correctly when I installed it years ago. However, the stock on/off assem works great. I may be missing "z valve" specific parts and orings, I don't know!

well it seems that the pin is too long......or maybe the pin oring that it seals is not the correct one

also how tight is the pin oring in the on off bottom? is there a lot of friction?


what happens when you pull and release the trigger very slowly?

[[NA]WARLORD]

Eclipse Classic, is that grey/black/silver splash ?

If so, would you be interested in selling the sight rail/tourney lock/va adapter ?

[stevewar]

Depends on where you want it. The 2 easiest imo are to T-off the nomal valve input and put the lpr there or get an ASA that has 2 ports and mount it below the grip. other than that your limited by imagination and budget. I know some ppl have mounted them inside the grip if theres room or on front like an AC.

I live in Vancouver (WA, no Canada). If we have any big games in my area that are worth the drive I'll let you know.

Hey thanks for the advice. I looked around and foudn the customer products dual ported ASA and am going to order that.

Looking forward to hearing about decent games comming up.

-Steve

[EclipseClassic]

Eclipse Classic, is that grey/black/silver splash ?

If so, would you be interested in selling the sight rail/tourney lock/va adapter ?

PM sent.

[EclipseClassic]

well it seems that the pin is too long......or maybe the pin oring that it seals is not the correct one

also how tight is the pin oring in the on off bottom? is there a lot of friction?


what happens when you pull and release the trigger very slowly?

There is a little friction between the old o ring and the pin. The pin is the only one I have that fits, and it is the one that came with the kit. The L7 pin isn't even close to being the right size. How loose is the pin supposed to fit. It seems like it sticks slightly when pushed out fully. I bet you the o ring is my problem. Ill have to gas it up and play with it some more, but the gun chuffs when the trigger is pulled back and the trigger does not reset for 1-2 secs after it fires. Letting off slowly doesn't do anything because there is no pressure. I did a quick search for "Z valve" and couldn't find anything.

[pump]

There is a little friction between the old o ring and the pin. The pin is the only one I have that fits, and it is the one that came with the kit. The L7 pin isn't even close to being the right size. How loose is the pin supposed to fit. It seems like it sticks slightly when pushed out fully. I bet you the o ring is my problem. Ill have to gas it up and play with it some more, but the gun chuffs when the trigger is pulled back and the trigger does not reset for 1-2 secs after it fires. Letting off slowly doesn't do anything because there is no pressure. I did a quick search for "Z valve" and couldn't find anything.

well try sliding the pin in and out of the on off bottom without the oring.....if there is still friction(there shouldnt be any) then thats is a problem


i think the main problem is the pin to top oring or the pin length

just more fiddling will tell