E-Mag Tech question

[Twistedpsyche]

Ok so I got ahold of a set of Emag lowers with Xmod 1.8. I installed them on my Tac One last night and I have a couple issues/questions.
1. For some reason when I air it up with the standard on/off (instead of the ULT) it either just leaks or farts the air out sounding like rapid fire. So is it ok to us the Emag with the ULT?

2. When I use it with the ULT it seems to work fine in Electronic mode with one exception. Sometimes the sear is not resetting properly. I am missing the saftey btw (will that make a big difference?). So when it does not reset itself I have to use a small tool to just push it forward and reset it.

3. It won't work in mech mode, period.

Any thoughts? Solutions?
Thanks.

[TnDeathInc]

Pin length - you might need to get an emag pin or shave down the one you have. Big E can quote what it needs to be off the top of his head or you can do a seach, i dont want to tell you wrong.

[robnix]

Ok so I got ahold of a set of Emag lowers with Xmod 1.8. I installed them on my Tac One last night and I have a couple issues/questions.
1. For some reason when I air it up with the standard on/off (instead of the ULT) it either just leaks or farts the air out sounding like rapid fire. So is it ok to us the Emag with the ULT?

2. When I use it with the ULT it seems to work fine in Electronic mode with one exception. Sometimes the sear is not resetting properly. I am missing the saftey btw (will that make a big difference?). So when it does not reset itself I have to use a small tool to just push it forward and reset it.

3. It won't work in mech mode, period.

Any thoughts? Solutions?
Thanks.

The ULT does not provide enough return force to rest the Emag sear, You need an Emag on/off, which has slightly different o-rings than the RT/Pro on/off , and an Emag length on/off pin.

[Ruler_Mark]

The ULT does not provide enough return force to rest the Emag sear, You need an Emag on/off, which has slightly different o-rings than the RT/Pro on/off , and an Emag length on/off pin.

RT/Pro on/off works fine in my gun with the emag length pin

[TnDeathInc]

i use standard rt on offs, some with the new orings some with the old, with shaved or purchased pins.

[BigEvil]

You need:

-Emag length on/off pin. .712 or smaller. I run mine from .700 down to .680 for higher ROF with the Xmag

-Emag specific black quad oring to replace the small one in the top of the on/off. (In the body)

-You also need to read up on the Xmod manual. There is a whole section showing you how to check the specs on the solenoid plunger. If it is too short, then it has trouble shooting. This is a very common occurrence. That plunger is loc-tited to the sear and after a while it breaks loose and spins all over the place. Also important, that whole plunger assembly should move 110% freely when its all together and you tilt the gun forward. They have a tendency to bend once in a while.

[Twistedpsyche]

Cool. Thanks a lot for all the info everyone. I'll definitely get on and review the manual. I was going to do it today, but I'm at work and the web store is one of the "restricted" sites at work. I'll get on there tonight when I get home.

Can I get a hold of a seperate on/off pin or do I need to go buy the entire on/off assembly?

Thanks again.

[athomas]

You can buy just the pin.

[Twistedpsyche]

You can buy just the pin.

Where? I didn't see it at tunamart.

[BAZOOKA_Boy]

buy one directly from AGD, they have them in the correct .712 pin length, and they also have quadoring packs, both of which you will need! good luck getting your Etach up and running!

[Twistedpsyche]

Excellent.
Once again. Thanks for the info.

[ProblemKinder]

if you're brave enough to ship first i would swap an Emag valve for an Xvalve.

[Twistedpsyche]

if you're brave enough to ship first i would swap an Emag valve for an Xvalve.

What's the difference? Isn't the Emag valve just an Xvalve made out of stainless steel?

[phizz]

emag valve is worth about $50 less when being bought used. Other then being stainless and a bit heavier functionally no difference.

Also you might want to try upping the dwell on the marker my old xmag wouldn't fire unless my dwell was around 19? at least I think thats what it was at it was a while ago now.

Oh and listen to BigEvil I can't say enough good things about his tech skills.

[Twistedpsyche]

Oh and listen to BigEvil I can't say enough good things about his tech skills.

I will. And thanks for the info on the valves.