Tac One feedneck

[Misha]

I was wondering if theres a thread and I could unscrew the feedneck to replace it with a clamping one. It is Angel threaded correct ? Will ion/epiphany feednecks match the threading ?

[michbich]

I was wondering if theres a thread and I could unscrew the feedneck to replace it with a clamping one. It is Angel threaded correct ? Will ion/epiphany feednecks match the threading ?

Although i don't know about the ion/epiphnay threads, i know that the tac one is Angel threaded. Remember, the strapwrench is your friend when dealing with feednecks. Don't go in there with visegrips and pliers.

[Looper]

I was wondering if theres a thread and I could unscrew the feedneck to replace it with a clamping one.

They can be removed, use a strap wrench

It is Angel threaded correct ?

Yes it is angel threaded.

Will ion/epiphany feednecks match the threading?

It is not the same thread and pitch but I have heard it is very close... It's best to use Angel.

You might want to check this thread out for more thread information...

http://www.pbnation.com/showthread.php?t=803907

[Misha]

Thanx guys! I dont have a strap wrench and was gonna use some padding and the regular wrench.

[Misha]

The reason i was asking was that i am trying to fit a q-loader on my Tac One and the feed elbow is very loose going into the standard feedneck. Maybe i should put some electrical tape there so elbow stays tight.

[Looper]

The reason i was asking was that i am trying to fit a q-loader on my Tac One and the feed elbow is very loose going into the standard feedneck. Maybe i should put some electrical tape there so elbow stays tight.

IIRC that is the exact place that I have heard use of the ION thread on a Tac Body was for the Qloader elbow kit.

Also before you try and remove the neck you might want to try and soften the loc-tight by running hot tap water over the body/neck area for a few minutes.

[Misha]

Would it be better if i just used some electrical tape wrapped over the elbow to have it fit snug into the feedneck ? I had no idea there was some loctite involved

[pk5]

you could, but it would look a bit ugly.

loc-tite can also be remove by heading up the part where the loc-tite is with a heat gun or a hair dryer. Even though heat work work a lot faster.

Also if it is blue loctite you can just twist it out, any idea which loctite this is?

[Misha]

Cant see it in the feedneck but the one used on the air hose is pink color

[sunjess]

you can get the ion mod kit for the tac-one. There is a feedneck that you will want to use that is included in that kit.

[papan]

what other kits can work with tac one

[sunjess]

what other kits can work with tac one

not sure if there are any other mods for the tac-one with a qloader. I went to there site and checked the mod kits. That is where it said to use the ion mod it. I also just ordered a CMS Upgrade from them also so I have more options for mounting my Q on my tac-one. When I get it in and have everything mounted I will post pictures for you

[papan]

Since i am new to all of this, what's a CMS upgrade?

not sure if there are any other mods for the tac-one with a qloader. I went to there site and checked the mod kits. That is where it said to use the ion mod it. I also just ordered a CMS Upgrade from them also so I have more options for mounting my Q on my tac-one. When I get it in and have everything mounted I will post pictures for you

[MechMags]

Since i am new to all of this, what's a CMS upgrade?

if its in reference to the q-loader then its the Custom Mounting Socket upgrade which gives the user much more versitility in mounting the q-loader system.