Need Warp Help

[Enhander]

Ok, so I got a Warp feed for my Tac...here it is:



Im having one problem with it. It works, but not 100%. Once I turn it on and load paint through it, once the paint is shot through the tube, I have to push the button on the bottom again to load more paint in the tube. Is this just because theres so much tension on the hose near the top of the feedneck? Or is there something up with the warp? Do I need to tape that button down so it keeps the motor spinning???

EDIT..I now know its sound activated. Ive tried every setting on AGD's Warp manuel and nothings working...Help??

[jonny72888]

you need to try a few things

did you read how to use the jumpers? if you have to many it might not spin. if you have it in the wrong spot it could not be in sound mode and in intilli mode waiting for the switch to close.

the fact that you can push the botton to feed them show that they feed just fine, but if you really want, take the hose off the gun and dry fire it and see if it spins.

post back and let me know how it goes.

[Tunaman]

2 things I see.
1-you need to use the 90 degree warp adapter in the feedneck to get rid of that sharp bend on top
2- you need to get some Superhose. That stock hose sucks..but should work with the 90 degree adapter.
The warp should spin on every shot, if not you need to adjust the sensitivity with the blue pttentiometer on the warp board. Make sure the jumpers are set for "sensor". Let us know...

[Enhander]

you need to try a few things

did you read how to use the jumpers? if you have to many it might not spin. if you have it in the wrong spot it could not be in sound mode and in intilli mode waiting for the switch to close.

the fact that you can push the botton to feed them show that they feed just fine, but if you really want, take the hose off the gun and dry fire it and see if it spins.

post back and let me know how it goes.

still no spin. I tired adjusting everything with the jumpers. Took the hose out too. Grant it im dry firing, I assume if it has paint in it it really doesnt matter..either way? Also, that sensitivty adjuster is pointed to the top, hasnt been turned at all. I gotta be doing something wrong. Since I have the intelli frame, my jumper should be set on negative right? Which is the top on the right set of jumpers. Should I even have my dwell set to anything? Right now I have 2 of the 4 jumpers on it.

[jonny72888]

do you have it hooked up to the frame or just sound?

[Enhander]

2 things I see.
1-you need to use the 90 degree warp adapter in the feedneck to get rid of that sharp bend on top
2- you need to get some Superhose. That stock hose sucks..but should work with the 90 degree adapter.
The warp should spin on every shot, if not you need to adjust the sensitivity with the blue pttentiometer on the warp board. Make sure the jumpers are set for "sensor". Let us know...

Do you sell the 90 degree adapter tuna?? Im new to all this warp feed stuff..so im a little lost. I know what you're talking about, the pttentoimeter is that blue thing that can be adjusted. Right now its set all the way to the top (i havent messed with it) I thought since i had an InteliFrame that the jumper needs to be set on negative?

If I put the sens jumper on and turn the adjustment wheel the motor doesnt start turning until its almost all the way on the other side. Once the motor starts spinning, i move it back just a tad so the motor stops. Still nothing.

[Enhander]

do you have it hooked up to the frame or just sound?

hooked to the frame?? im sorry i sound so ignorant, this is my first warp feed.

[jonny72888]

hooked to the frame?? im sorry i sound so ignorant, this is my first warp feed.

you can have a switch in the frame so everytime you pull the trigger it feeds a ball into the gun. or you can have it with just sound.
if you do not have the switch in the frame then the jumpers have nothing to do with the fame and should only be used to make it work on sound.

[Enhander]

you can have a switch in the frame so everytime you pull the trigger it feeds a ball into the gun. or you can have it with just sound.
if you do not have the switch in the frame then the jumpers have nothing to do with the fame and should only be used to make it work on sound.

ok, 2 questions then,
1) where can i get a switch to do that?
2) If they arnt avaible anymore, what do my jumper settings need to be?

[jonny72888]

ok, 2 questions then,
1) where can i get a switch to do that?
2) If they arnt avaible anymore, what do my jumper settings need to be?

radio shack, you can get all the parts for about $7 and be done in about 30min.

your jumpers need to be set to sound only.

[Enhander]

radio shack, you can get all the parts for about $7 and be done in about 30min.

your jumpers need to be set to sound only.

so i take it that has to be set on the "sens" jumper and then mess around with the adjustment knob?

what parts do I need to get at radio shack??

again im sorry, i feel like an idiot asking all this stuff, but i just want the thing to work.

[jonny72888]

so i take it that has to be set on the "sens" jumper and then mess around with the adjustment knob?

what parts do I need to get at radio shack??

again im sorry, i feel like an idiot asking all this stuff, but i just want the thing to work.

a switch, wire, 3/32 mono male plug.

see the wire and switch, you will need to do something like that.
or just run it with the sensor.

yes the jumper has to be set to sens and the move the knob around till it feeds on every shot.

[Enhander]

Ok, thanks man. Good news to report.
I put the jumper on sens and moved the knob around a bit. The motor now turns a bit every time i fire. I take it its not going to spin a huge amount right? It spins a little bit every time a shoot the gun.
Ill get a chance to test it 100% tomorrow, and run some paint through it, but does it sound to you that its working properly now?

[jonny72888]

Ok, thanks man. Good news to report.
I put the jumper on sens and moved the knob around a bit. The motor now turns a bit every time i fire. I take it its not going to spin a huge amount right? It spins a little bit every time a shoot the gun.
Ill get a chance to test it 100% tomorrow, and run some paint through it, but does it sound to you that its working properly now?

yes, ok now with the other jumpers you can adjust how long it spins for. i think it the less jumpers the more it spins, i think... it coould be the other way around.

[jonny72888]

http://www.airgundesignsusa.com/downloads/intelliwarp.pdf