My E-Mag won't Fire.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Ratzo
    Registered User
    • Feb 2004
    • 352
    #1

    My E-Mag won't Fire.

    So after having my Micro E-Mag since before Christmas, I was finally able to get the battery charged.
    When I put the pack on the marker, the grip would read AGD 1.35 for a few seconds then the screen would go blank and it would not fire. This is on a fully charged pack.
    Does the screen usually read something when the marker is ON?
    Any help would be greatly appretiated.
    Tags: None
    • csallen039
      Registered User
      • Feb 2008
      • 182
      #2
      The screen goes off after about 5 seconds. You'll know that its on because one pixle will flash at a slow rate.

        Comment

        • BigEvil
          www.BigEvilOnline.com

          • Feb 2005
          • 9333
          #3
          Hopefully this is a simple fix. See if the trigger magnet is too far in. Back it out a little and see if it helps.

          If not, the next step is to check all of your connections. The screw that holds the controller board in is very important. That is the ground. Make sure it is snug, and that there is no corrosion on it. If the gun was re-annoed, the area around the hole for that screw should be sanded or wire brushed down to the bare metal (Without damaging it) so that the board can get a good connection to the frame.

          Report back your findings.

            Comment

            • VTLO910
              Ballin' since early '90s..
              • Jan 2008
              • 215
              #4
              It's junk, save yourself the trouble and get rid of it... PM me, I'll take the scrap for parts, I'll give you my address to send it to...

                Comment

                • Ratzo
                  Registered User
                  • Feb 2004
                  • 352
                  #5
                  Yes there is a pixel that does flash every now and then.
                  I was able to get it to cycle a few times but not cosistently.
                  I did notice that there is some rusty dust on the magnet on the trigger.
                  I'll have to look further into the grip frame and see about the magnet setting.

                    Comment

                    • athomas
                      Of course it works-its AGD
                      • Jan 2002
                      • 8039
                      #6
                      Try the trigger magnet adjustment first. If that doesn't work, try reversing the magnet on the back of the trigger. If it is backwards, it won't work.
                      Except for the Automag in front, its usually the man behind the equipment that counts.

                        Comment

                        • KevinA
                          Registered User
                          • Feb 2008
                          • 348
                          #7
                          Originally posted by VTLO910
                          It's junk, save yourself the trouble and get rid of it... PM me, I'll take the scrap for parts, I'll give you my address to send it to...
                          Genious!!!

                            Comment

                            • VTLO910
                              Ballin' since early '90s..
                              • Jan 2008
                              • 215
                              #8
                              you never PM'd me for my address... I'm still here to take your garbage...lol

                                Comment

                                • Tao
                                  Registered User
                                  • Jan 2006
                                  • 834
                                  #9
                                  Originally posted by Ratzo
                                  Yes there is a pixel that does flash every now and then.
                                  I was able to get it to cycle a few times but not cosistently.
                                  I did notice that there is some rusty dust on the magnet on the trigger.
                                  I'll have to look further into the grip frame and see about the magnet setting.

                                  First try it on mechanical mode (without the electronics on) and tell us what happens.

                                    Comment

                                    Previous template Next
                                    Working...