so...i want to build a rising phoenix emag....

[pk5]

hi everyone.

So i want to build a rising phoenix emag - x valve - pneu

What can i do and what would i need?

1) Phoenix body ( 430 ish)
2) emag frame ( 230 ish)
3) Pneu kit?
4) X valve level 10 ~ 180 ish?
5) Anything else??????

I need to put all the cost together, so i can start saving and know how much i need.

Is there a discrete place to put the lpr? Will the emag frame have enough spaces?

Thanks

[nevtangle]

hi everyone.

So i want to build a rising phoenix emag - x valve - pneu

What can i do and what would i need?

1) Phoenix body ( 430 ish)
2) emag frame ( 230 ish)
3) Pneu kit?
4) X valve level 10 ~ 130 ish?
5) Anything else??????

I need to put all the cost together, so i can start saving and know how much i need.

Is there a discrete place to put the lpr? Will the emag frame have enough spaces?

Thanks

How are you going to put pneumatics in the emag? It's going to be one or the other. You'll have to make up your mind and figure out which one you want. Either a pneumag or an emag. You won't need an lpr for the emag.

[pk5]

so something like this can't be done?

http://automags.org/forums/showthrea...hlight=pneumag

[TwilightG]

How are you going to put pneumatics in the emag? It's going to be one or the other. You'll have to make up your mind and figure out which one you want. Either a pneumag or an emag. You won't need an lpr for the emag.

Unless he's using a gutted E-Mag frame?
Personally, I think it'd be a bit heavy and bulky considering it would have pneu internals.

If you're talking Electr-pneumatic, that's a whole other beast and you wouldn't want to use an E-Mag (not stock internals anyway)

[pk5]

So the only choice would be a gutted emag frame, with pneumatic internal and use this

http://www.airsoldier.com:8080/cgi-bin/mivavm?Merchant2/merchant.mvc+Screen=PROD&Store_Code=AOS&Product_Code=SMC-S070C-SDG-32&Category_Code=SOLENOIDS

instead of the mechanical 3 way?

[nevtangle]

Oh, that makes more sense. Don't forget that you'll need a board as well. Everyone seems to be pretty excited about the universal t boards. As for your choice of solenoids, I don't have much experience and can't really help you there.

So the only choice would be a gutted emag frame, with pneumatic internal and use this

http://www.airsoldier.com:8080/cgi-bin/mivavm?Merchant2/merchant.mvc+Screen=PROD&Store_Code=AOS&Product_Code=SMC-S070C-SDG-32&Category_Code=SOLENOIDS

instead of the mechanical 3 way?

And I wouldn't say that the emag frame is your only choice, but if that is what you want to use then it'll work.

[Smoothice]

i think you need to up your budget on an x valve with level 10. More like $180-200

[Madmarx]

if you're looking to get complete emag lowers you're going to spend 3-400.
If you're only looking for a gutted frame then you may be close.

[joelbird]

lpr in the emag battery housing..... something like this?

[questionful]

I think E-mag lowers are a bad choice for an e-pneu frame. Get something cheaper.

[Enemy]

basically you dont need to use emag lowers if you are going to use an e-pnue converstion.. another frame can be used.. also if you do still want an emag frame then the battery can be dropped but i dont believe the board would be of use for you either.

[pk5]

ooo ok

Maybe i should just go with a regular emag lower and add the phoenix body then.

thanks

[seekandestroy78]

to make and ep mag you dont have to start with an e mag. people are putting t-boards in everything these days. hell it would probably fit in one of the ule slots in my rail.

[MournBlade]

to make and ep mag you dont have to start with an e mag. people are putting t-boards in everything these days. hell it would probably fit in one of the ule slots in my rail.

If you can fit the bottom of a 9v battery in one of the slots then, yes it will fit.

[Ruler_Mark]

you could use the HES and emag sear and make a eletrco puematic or mech design,useing the front battery housing for the 9vbattery and lpr. a ram isntead of the solenoid in a emag