Freak Question!

[Ruler_Mark]

Ok here is the issue,

I sold a gun that was working.

Buyer recieves it and Claims it is not working. Buyer finds a possible fault, caused by who knows. Buyer and I Spend alot of time trying to track down the issue. We both live in florida so altitude and temps are rather close. After swaping out every part individually it is rulled that once the trigger frame is swapped it works. Odd? On a straight edge the front of the trigger frame is a few thousanths of an inch bent downward, god knows how this happened.

After many more phone calls it is determined that I thought it was working because i run my emags at 1000psi, buyer runs his at ~850psi.

So I agree to issue a full refund and everyone except me can be happy.

I recieve the gun back, Air it up adjust my dynaflow down to 750psi for poops and giggles and It shoots.



ANY Ideas?

proof of working:

http://modmymag.com/images/tiger/MVI_0531.avi

Shot on a camera, so sound gets peaked out thats why the shot doesnt sound that loud.
sorry it goes out of focus, or I cant do 18bps+ FA neighbors dont like it

[PhoenixWolf]

It's possible his regulator is faulty and is NOT outputting proper pressure. Or he backed the velocity screw out too far, or he put it in so far it vented. Other possibilities: he overtightened valve or mainbody screws, or he needs a different on/off pin length.

[Ruler_Mark]

It's possible his regulator is faulty and is NOT outputting proper pressure. Or he backed the velocity screw out too far, or he put it in so far it vented. Other possibilities: he overtightened valve or mainbody screws, or he needs a different on/off pin length.

Trust me,, several of each part were tested and all possible configurations were tested. Atleast he claims on his end.

I simply aired it up exactly as return shipped, except freshly charged battery and fireblade(moved the tuna to my xmag)

[PhoenixWolf]

That could have done it. Hall effect trigger. If the trigger magnet was in too far on one of the triggers, the gun doesn't fire.

[Ruler_Mark]

That could have done it. Hall effect trigger. If the trigger magnet was in too far on one of the triggers, the gun doesn't fire.

The solenoid was tripping, on his end. It didnt even work in mech mode.

[Looper]

The solenoid was tripping, on his end. It didnt even work in mech mode.

Had this happen to me on a RED ULE EMag I just bought; it wouldn't even fire on Mechanical mode when I got it. Stripped it down and reassembled and it worked like a charm. Not sure if the on/off pin was engaging or not. I saw nothing wrong when I tore it down and have not been able to get it to act up again... go figure... Blame it on "Mercury in Retrograde"

[Ruler_Mark]

Had this happen to me on a RED ULE EMag I just bought; it wouldn't even fire on Mechanical mode when I got it. Stripped it down and reassembled and it worked like a charm. Not sure if the on/off pin was engaging or not. I saw nothing wrong when I tore it down and have not been able to get it to act up again... go figure... Blame it on "Mercury in Retrograde"

I wish it was that simple but it was taken apart etc.

The buyer isnt an idiot when it comes to guns etc so it cannot be that.


Just looking for more freak answers

[PhoenixWolf]

Okay, so it's different lowers, same uppers? Is it the same rail? I need a list of every part that is different between his and your configurations for it.

[Ruler_Mark]

Okay, so it's different lowers, same uppers? Is it the same rail? I need a list of every part that is different between his and your configurations for it.

All speaking from when he had it
Body - Replaced no change
Valve - Replaced no change
Rail - Replaced no change
BattPack - Recplaced no change
Triggerframe - replaced and it fired
Sear - replaced nochange

each part being swapped out individually.

[ajnin]

Throw it in a box... send it to me.

[Ruler_Mark]

Throw it in a box... send it to me.

sure I just require some payment.



This is just boggling me.