Emag not shooting correctly

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • DamianTC
    Emag - ULE RT - Classic
    • Sep 2008
    • 272
    #1

    Emag not shooting correctly

    ok brand new Emag from tuna. Aired it up for the first time. Trigger will click but not firing in both modes E or M. I then took the tank off and back on, and this time it fires in E and M but after 10-20 shots it goes back to just clicking. After about 10 to 15 seconds after it stops firing and starts clicking, air will start to leak out of the Level 10. Only thing I can do is disconnect the tank and air it back up and does the same thing, fires a few shots then goes to clicking then leaks out the Level 10.

    I am kinda confused over this, I just started with the problem but figured I would put a thread up here to help me along the way. If you need anymore info from me, just ask.

    Thanks,
    Damian
    Tags: None
    • dark blade
      I<3AGD|WGP|WDP|APS|CCI|CCM
      • Apr 2008
      • 733
      #2
      umm... input pressure on the tank? tank pressure? did you just get the emag? does it leak when you hold the trigger back in mech mode? if not then its your level ten. if it leaks after the pin is pulled back then its the on/off pin or further back.

      test that and let us know.

      Start with tank pressure and if its above 750 (if its a normal HP tank it should be) and then move on to the regulator pressure at the back of the gun. then pull the trigger and check, then report back here and let us know what happens

        Comment

        • BigEvil
          www.BigEvilOnline.com

          • Feb 2005
          • 9333
          #3
          -Make sure there is over 800 psi in the tank and that it is not a LP reg on it.

            Comment

            • DamianTC
              Emag - ULE RT - Classic
              • Sep 2008
              • 272
              #4
              I tested with 2 tanks. a Nitroduck I-Reg with 1000psi output and an AGD FlatLine, was set between 800-900psi.

              I adjusted the reg pressure on the x-valve just about all the way up and down with same results

              It wasnt leaking, more like venting because it wouldnt start leaking until afew minutes after the gun stoped firing.

              Even when the gun stopped firing, the sear pin still stuck out and had pressure behind it when you pull the trigger.

              I went ahead and oiled the valve, and now when I gas it up, it doesnt shot at all. The sear pin still has pressure behind the trigger, but doesnt fire in any mode E or M. There is no leak in the gun at any point in the gun now.

              The Emag is brand new from tunamart

                Comment

                • bjyourk
                  Registered User
                  • Sep 2006
                  • 205
                  #5
                  Did you really torque that valve screw down? It's my understanding that if that happens, it will set the bolt off just enough to not allow the bolt to cycle.

                    Comment

                    • DamianTC
                      Emag - ULE RT - Classic
                      • Sep 2008
                      • 272
                      #6
                      Did you really torque that valve screw down?
                      no, its just hand tight.

                      when there is air in the gun, there is pressure behind the trigger and it clicks when you pull the trigger, it just doesnt fire. That is the problem it currently has

                        Comment

                        • secretweaponevan
                          Only HALF Polish!
                          • Sep 2007
                          • 1132
                          #7
                          Originally posted by DamianTC
                          no, its just hand tight.

                          when there is air in the gun, there is pressure behind the trigger and it clicks when you pull the trigger, it just doesnt fire. That is the problem it currently has
                          It sounds like it is just that your lvl 10 is out of whack. Retune it.

                            Comment

                            • DamianTC
                              Emag - ULE RT - Classic
                              • Sep 2008
                              • 272
                              #8
                              Evan was right.

                              just had to tune the lvl10, the carrier came 2 sizes too tight.. bolt wasnt moving.. gun wasnt firing. all fixed now.

                              Its amazing how easy it is to overlook such simple things like that when you are so excited to have a brand new Emag in your hands... thats why we have AO

                              thanks guys

                                Comment

                                • secretweaponevan
                                  Only HALF Polish!
                                  • Sep 2007
                                  • 1132
                                  #9
                                  Originally posted by DamianTC
                                  Evan was right.

                                  just had to tune the lvl10, the carrier came 2 sizes too tight.. bolt wasnt moving.. gun wasnt firing. all fixed now.

                                  Its amazing how easy it is to overlook such simple things like that when you are so excited to have a brand new Emag in your hands... thats why we have AO

                                  thanks guys
                                  Glad you got it working.

                                    Comment

                                    Previous template Next
                                    Working...