Leaking bettween two halves of valve.

[Aliens-8-MyDad]

ok i dun know whats goin on with this thing but its leaking between the two halves of the valve. i put in a new reg seat and it still is leakin also awhile ago i tried taking the reg pin and the spring got streched so i couldnt get it back in so i bent it and stuff im thinkin thats the problem, do i really have to buy a whole new spring, i dont want to... here is a pic its kinda blurry, camera was focusin on wrong thing.

*Pic removed because you can't even tell what the pic is of.*

[Aliens-8-MyDad]

BTW i put some AGD auto lube on it so thats why u see bubles

[MAGS own YOU]

I cant really see anything its too blurry. Is your spring really stretched out?

[Aliens-8-MyDad]

well i shuved it all in there so now the spring makes that little pin that stiks out go to the left side alot it isnt centerd.

[soilent green]

that shouldn't make it leak however it should be replaced if it is really leaking between the reg and valve body then it must be the big fat O ring on the reg

[EnW]

yeah...check the o-ring on the back half of the reg. The spring shouldn't matter...but if you really think you need a new one let me know. I have an extra spring and pin that are brand new. I will let you have them cheap.
BTW...is that supposed to be a picture of something??

[Thordic]

Thats the blurriest picture I've ever seen :)

First thing that comes to my mind though is the reg oring. Its the fat whitish/yellow one between the halves. Replace it and see what happens.

My spring is a little bent too, but it never gave me problems.

[Aliens-8-MyDad]

alright am i the only one that can see in that picture? if ro go to the very right lower corner u can see the trigger frame handel thing. then u look up and see the air fitting comming out and look to the side and u see a blurry valve with soem bubles... ok well i replaced that o-ring and it still leaks i got it twisted all the way and i noticed that the two halves dont line up exactly... where it says min-imag why dont those line up and my tank has very little air in it so is it leaking because there is not eniff presure in the valve to seal it? ok thxs...

[soilent green]

you either didn't twist it far enough or it isn't really leaking beetween the halves try your local proshop its hard for us to help you if we can't have our hands on it

[Aliens-8-MyDad]

i got it screwd more than enuff, it is past the point where the word minimag lines up. and it is leaking bettween the halves because 1 i can hear it, 2 i can feel the air commin out, 3 i put oil on it and it starts bubling. and im not talkin it to my proshop. last time it was acting wierd they said my on off assembly was broken with out looking. i weent to the tabel took out the valve and it was fine, really they needed to fill up the tank and they didnt.

[soilent green]

it happened to me last night after I took it apart and reassembled it it still leaked and I found no problems I checked my velocity and realized it was really low after turning it up alot it stoped leaking

[Aliens-8-MyDad]

hmm well my verlocity is up almost as high as it will go, must be becasue there isnt barly any air in my tank. it doesnt even kick out the sear. ok so ill just fill my tank and hope it works..

[Blennidae]

Just a suggestion: Take a look at that exploded diagram of the retro valve and make sure you have everything seen in the picture. Maybe you missd something?

[Aliens-8-MyDad]

.... its not a retro valve..

[soilent green]

just remember mags do weird stuff when they aren't adjusted at least close to what they are suppossed to be but I think maybe there isn't enough pressure to seal the o ring just an idea