Hyperframe help!

[BIP8ntball]

I have a 13pbs hyperframe. I assume this because semi only goes to 13, and hyper(ramp) is limited to 10bps. Is there anywhere that can flash the board/update software/provide a new board for teh frame in order to get a higher rof? Any help would be appreciated

[211]

You could put a Universal Tboard in it
that would give it as much ROF as you want, plus any mode of fire you may want, and it would let you put eyes on

[fierymartel]

Well, since it's up. Lets say we use a UTB. We put grips on the frame without the window for the LCD. Is it then possible to mount a LED in place of one of the buttons and mount a button in the bottom hole?
It would be convenient if we could do this and not alter the frame. Or maybe use both buttons and use LED through window to program?

[BIP8ntball]

The gun has a bolt that says "ANS phase ll" and has a foamy in the middle, and the regulator is black and says "lab" or "eae". How fast of a ROF would I be able to achieve before I start to chop with say a revy or even a halo b? I just got the gun and know very little about it other than its got a hyper frame and a sweet splash kit, haha.

Also, This UTB, will it fit without modding the frame or am I gunna have to cram everything in there?

[Coralis]

See for yourself http://www.scenariodreams.com/produc...rsaltboard.htm

[BIP8ntball]

See for yourself http://www.scenariodreams.com/produc...rsaltboard.htm

bur from a mag standpoint....how many bps could my gun handle b4 it chops like a mofo with ^^^ that setup?

[fierymartel]

classics can shoot about 16 bps without shoot down (so I've been told). With that aside, the feed rate of your hopper will have more to do with whether or not you chop. If you put a level 10 bolt on your valve, it will stop on a ball before it will chop it (no matter how fast it is cycling).
I have a hyperframe, I just can't get it to fire 1 shot at a time. I think a ULT will fix this. However, I won't shoot this without a level 10 bolt. If a ball gets hung up or something, a 20 bps hyperframe can make some quick paint soup. That won't happen with level 10. I hope I've answered your question. Again, chopping has more to do with feed rate vs cycle rate.

[maniacmechanic]

13's not fast enough ? , just find a 20 bps board & put in it
Big Evil knows a lot about Hyper frames , he says " The BEST thing you could ever to to that hyperframe is REPLACE THE BOARD!! The T-board works very well and is my choice these days "

[BIP8ntball]

13's not fast enough ? , just find a 20 bps board & put in it
Big Evil knows a lot about Hyper frames , he says " The BEST thing you could ever to to that hyperframe is REPLACE THE BOARD!! The T-board works very well and is my choice these days "

I just suck at soldering and I dont want to spend over 60 bux or so to get an extra 3bps chop free. but the extra modes would be nice, even if i capped it at 15. theboard+eyes, plus the install and milling, id be looking at like 10 or more

does anyone know where I can find a 20bps board? and/or a flat double trigger (blade style)??

[Ando]

Luke for the trigger...

http://lukescustoms.com/page0012.htm

...and the board...can't help ya with. T-Boards can be purchased at

http://www.scenariodreams.com/productpages/universaltboard.htm

[fierymartel]

Lukes Customs makes the trigger you are looking for. I have a 20 board in my frame. I think 13 is probably enough.

[fierymartel]

My problem is do I use a classic valve or x valve?

[BIP8ntball]

My problem is do I use a classic valve or x valve?

30 for the trigger seems a little steep especially without shipping included

would you be willing to swap boards :)

[fierymartel]

Probably not. I think my 20 bps board is pretty rare and I'm trying to create a piece to sell.

[Coralis]

I run my hyperframed micromag set on turbo mode and 9bps with halo sound activated backman hopper (this is a non power feed model) and very rarely have problems , in fact i dont usually carry a squeegee any more. I'm still using a level 7 bolt as well.